![background image](http://html.mh-extra.com/html/national-semiconductor/cp3bt26/cp3bt26_user-manual_710369027.webp)
27
www.national.com
CP3
BT26
IPRE
The Preliminary Idle bit controls whether an
idle cycle is inserted prior to the current bus
cycle, when the new bus cycle accesses a dif-
ferent zone. No idle cycles are required for on-
chip accesses.
0
–
No idle cycle (recommended).
1
–
Idle cycle inserted.
6.4.4
Static Zone 1 Configuration Register (SZCFG1)
The SZCFG1 register is a word-wide, read/write register
that controls the timing and bus characteristics for off-chip
accesses selected with the SEL1 output signal.
At reset, the register is initialized to 069Fh. The register for-
mat is shown below.
WAIT
The Memory Wait field specifies the number
of TIW (internal wait state) clock cycles added
for each memory access, ranging from 000b
for no additional TIW wait cycles to 111b for
seven additional TIW wait cycles. These bits
are ignored if the SZCFG1.FRE bit is set.
HOLD
The Memory Hold field specifies the number
of Thold clock cycles used for each memory
access, ranging from 00b for no Thold cycles
to 11b for three Thold clock cycles. These bits
are ignored if the SZCFG1.FRE bit is set.
RBE
The Read Burst Enable enables burst cycles
on 16-bit reads from 8-bit bus width regions of
the address space. This bit is ignored when
the SZCFG1.FRE bit is set or the
SZCFG1.BW is clear.
0
–
Burst read disabled.
1
–
Burst read enabled.
WBR
The Wait on Burst Read bit controls if a wait
state is added on burst read transaction. This
bit is ignored, when SZCFG1.FRE bit is set or
when SZCFG1.RBE is clear.
0
–
No TBW on burst read cycles.
1
–
One TBW on burst read cycles.
BW
The Bus Width bit controls the bus width of the
zone.
0
–
8-bit bus width.
1
–
16-bit bus width.
FRE
The Fast Read Enable bit controls whether
fast read bus cycles are used. A fast read op-
eration takes one clock cycle. A normal read
operation takes at least two clock cycles.
0
–
Normal read cycles.
1
–
Fast read cycles.
IPST
The Post Idle bit controls whether an idle cycle
follows the current bus cycle, when the next
bus cycle accesses a different zone.
0
–
No idle cycle.
1
–
Idle cycle inserted.
IPRE
The Preliminary Idle bit controls whether an
idle cycle is inserted prior to the current bus
cycle, when the new bus cycle accesses a dif-
ferent zone.
0
–
No idle cycle.
1
–
Idle cycle inserted.
6.4.5
Static Zone 2 Configuration Register (SZCFG2)
The SZCFG2 register is a word-wide, read/write register
that controls the timing and bus characteristics for off-chip
accesses selected with the SEL2 output signal.
At reset, the register is initialized to 069Fh. The register for-
mat is shown below.
WAIT
The Memory Wait field specifies the number
of TIW (internal wait state) clock cycles added
for each memory access, ranging from 000b
for no additional TIW wait cycles to 111b for
seven additional TIW wait cycles. These bits
are ignored if the SZCFG2.FRE bit is set.
HOLD
The Memory Hold field specifies the number
of Thold clock cycles used for each memory
access, ranging from 00b for no Thold cycles
to 11b for three Thold clock cycles. These bits
are ignored if the SZCFG2.FRE bit is set.
RBE
The Read Burst Enable enables burst cycles
on 16-bit reads from 8-bit bus width regions of
the address space. This bit is ignored when
the SZCFG2.FRE bit is set or the
SZCFG2.BW is clear.
0
–
Burst read disabled.
1
–
Burst read enabled.
WBR
The Wait on Burst Read bit controls if a wait
state is added on burst read transaction. This
bit is ignored, when SZCFG2.FRE bit is set or
when SZCFG2.RBE is clear.
0
–
No TBW on burst read cycles.
1
–
One TBW on burst read cycles.
BW
The Bus Width bit controls the bus width of the
zone.
0
–
8-bit bus width.
1
–
16-bit bus width.
7
6
5
4
3
2
0
BW
WBR
RBE
HOLD
WAIT
15
12
11
10
9
8
Reserved
FRE
IPRE
IPST
Res.
7
6
5
4
3
2
0
BW
WBR
RBE
HOLD
WAIT
15
12
11
10
9
8
Reserved
FRE
IPRE
IPST
Res.