manualshive.com logo in svg

National Semiconductor CP3BT26, User Manual

The National Semiconductor CP3BT26 user manual is an essential companion for efficiently operating this cutting-edge product. With just a few clicks, users can conveniently download this comprehensive manual for free from our website, ensuring seamless navigation and superior performance.

Share
Download
background image

www.national.com

212

CP3BT26

IxCEN

The Timer x Interrupt C Enable bit controls in-
terrupt requests triggered on the correspond-
ing IxCPD bit being set. The associated
IxCPD bit will be updated regardless of the
value of the IxCEN bit.
0 – Disable system interrupt request for the

IxCPD pending bit.

1 – Enable system interrupt request for the Ix-

CPD pending bit.

IxDEN

Timer x Interrupt D Enable bit controls inter-
rupt requests triggered on the corresponding
IxDPD bit being set. The associated IxDPD bit
will be updated regardless of the value of the
IxDEN bit.
0 – Disable system interrupt request for the

IxDPD pending bit.

1 – Enable system interrupt request for the

IxDPD pending bit.

27.2.5

Interrupt Pending Register (INTPND)

The INTPND register is a word-wide read/write register
which contains all 16 interrupt pending bits. There are four
interrupt pending bits called IxAPD through IxDPD for each
timer subsystem. Each interrupt pending bit is set by a hard-
ware event and can be cleared if software writes a 1 to the
bit position. The value will remain unchanged if a 0 is written
to the bit position. All interrupt pending bits are cleared (0)
upon reset.

IxAPD

The Timer x Interrupt A Pending bit indicates
that an interrupt condition for the related timer
subsystem has occurred. Table 80 on page
209 lists the hardware condition which causes
this bit to be set.
0 – No interrupt pending.
1 – Timer interrupt condition occurred.

IxBPD

The Timer x Interrupt B Pending bit indicates
that an interrupt condition for the related timer
subsystem has occurred. Table 80 on page
209 lists the hardware condition which causes
this bit to be set.
0 – No interrupt pending.
1 – Timer interrupt condition occurred.

IxCPD

The Timer x Interrupt C Pending bit indicates
that an interrupt condition for the related timer
subsystem has occurred. Table 80 on page
209 lists the hardware condition which causes
this bit to be set.
0 – No interrupt pending.
1 – Timer interrupt condition occurred.

IxDPD

The Timer x Interrupt D Pending bit indicates
that an interrupt condition for the related timer
subsystem has occurred. Table 80 on page
209 lists the hardware condition which causes
this bit to be set.
0 – No interrupt pending.
1 – Timer interrupt condition occurred.

27.2.6

Clock Prescaler Register 1 (CLK1PS)

The CLK1PS register is a word-wide read/write register.
The register is split into two 8-bit fields called C1PRSC and
C2PRSC. Each field holds the 8-bit clock prescaler com-
pare value for timer subsystems 1 and 2 respectively. The
register is cleared at reset.

C1PRSC

The Clock Prescaler 1 Compare Value field
holds the 8-bit prescaler value for timer sub-
system 1. The counter of timer subsystem is
incremented each time when the clock pres-
caler compare value matches the value of the
clock prescaler counter. The division ratio is
equal to ( 1). For example, 00h is a
ratio of 1, and FFh is a ratio of 256.

C2PRSC

The Clock Prescaler 2 Compare Value field
holds the 8-bit prescaler value for timer sub-
system 2. The counter of timer subsystem is
incremented each time when the clock pres-
caler compare value matches the value of the
clock prescaler counter. The division ratio is
equal to ( 1).

27.2.7

Clock Prescaler Register 2 (CLK2PS)

The Clock Prescaler Register 2 (CLK2PS) is a word-wide
read/write register. The register is split into two 8-bit fields
called C3PRSC and C4PRSC. Each field holds the 8-bit
clock prescaler compare value for timer subsystems 3 and
4 respectively. The register is cleared at reset.

C3PRSC

The Clock Prescaler 3 Compare Value field
holds the 8-bit prescaler value for timer sub-
system 3. The counter of timer subsystem is
incremented each time when the clock pres-
caler compare value matches the value of the
clock prescaler counter. The division ratio is
equal to ( 1).

C4PRSC

The Clock Prescaler 4 Compare Value field
holds the 8-bit prescaler value for timer sub-
system 4. The counter of timer subsystem is
incremented each time when the clock pres-
caler compare value matches the value of the
clock prescaler counter. The division ratio is
equal to ( 1).

7

6

5

4

3

2

1

0

I2DPD I2CPD I2BPD I2APD I1DPD I1CPD I1BPD I1APD

15

14

13

12

11

10

9

8

I4DPD I4CPD I4BPD I4APD I3DPD I3CPD I3BPD I3APD

15

8

7

0

C2PRSC

C1PRSC

15

8

7

0

C4PRSC

C3PRSC

Summary of Contents for CP3BT26























































































































































































































































































Reviews:

No comments

Related manuals for CP3BT26

Baracoda All in One Printer Communication Protocol Manual preview
All in One Printer
Brand: Baracoda Pages: 42
Acconeer A111 User Manual preview
A111
Brand: Acconeer Pages: 32
Salusfin SF-930EU User'S Installation Manual preview
SF-930EU
Brand: Salusfin Pages: 6
TC Electronic DB6 User Manual preview
DB6
Brand: TC Electronic Pages: 174
TC Electronic Finalizer Express User Manual preview
Finalizer Express
Brand: TC Electronic Pages: 33
ekwb EK-FC780 GTX Jetstream Installation And Mounting Manual preview
EK-FC780 GTX Jetstream
Brand: ekwb Pages: 2
ZALMAN RESERATOR 1 Manual preview
RESERATOR 1
Brand: ZALMAN Pages: 22
Renesas RL78/G1H User Manual preview
RL78/G1H
Brand: Renesas Pages: 941
Juniper NFX250 Quick Start Manual preview
NFX250
Brand: Juniper Pages: 7
Galaxy Hunter Series Quick Start Manual preview
Hunter Series
Brand: Galaxy Pages: 30
Aaeon SBC-657B Manual preview
SBC-657B
Brand: Aaeon Pages: 61
ACTi LPR-100 Quick Installation Manual preview
LPR-100
Brand: ACTi Pages: 14
Lindy 32116 User Manual preview
32116
Brand: Lindy Pages: 12
Gundermann VIDEOWALL LEDWALL Optimizer HQ P2 Manual preview
LEDWALL Optimizer HQ P2
Brand: Gundermann VIDEOWALL Pages: 12
IEI Technology PE-6S-R40 User Manual preview
PE-6S-R40
Brand: IEI Technology Pages: 4
CyberResearch CPBF PMX-233 User Manual preview
CPBF PMX-233
Brand: CyberResearch Pages: 59
nox Hummer H-240CL Manual preview
Hummer H-240CL
Brand: nox Pages: 16
Valcom VIP-997 Manual preview
VIP-997
Brand: Valcom Pages: 4

Brands by name

Popular brands

Load more brands