CHANGES FROM PREVIOUS EDITION
The following changes have been made to this manual (WI1148A) since the previous edition (WI1148).
•
Removed the following entries from the index: Change Pulse Output to Cadence, Enable Chirp on RF Arming, Enable Transmitter Telco 1,
Enable Transmitter Telco 3, Select Bell Output on RF Arming.
•
Page 4, top, "Downloading From a Computer", the following sentence was added: "Unattended downloading from a computer is not allowed
for Fire Alarm or UL installations."
•
Page 6, "Panel Zone Doubling", the second sentence was modified and now reads, "The 16 zones will remain EOL terminated zones…".
•
Pages 4, 5, 7 and 14, the "50mS Loop Response Zones" entries now contain the following notation: "
Note:
750mS is required for Loop Re-
sponse time in UL installations."
•
Page 8, the "Auto Bypass Re-entry Zones" entry was modified: "Not Evaluated by UL" notation was added.
•
Page 9, the "Enter User Codes" entry was modified, and now states to "enter a code from 3 to 6 digits."
•
In the Area Options/Explanation chart at the top of page 10, the following information was added: "Ambush: Allows user code to send Am-
bush signal to Central Station".
•
Top of page 25, under the heading, "Output Timeouts", the following reference was added: "Not UL listed for Commercial Installations".
•
Page 27, Address 0720, bit 7 (Change Pulse Output to Temporal Output) was modified with the following notation: "This feature must be pro-
grammed in Fire Alarm applications."
•
Page 39, Table 4: The following notation was added: "Keypad Tamper must be enabled in UL installations."
•
Page 27--All references to 0720-Bit 6--"Enable PGM2 Chirp on Keyfob Arming" name changed to "Chirp Output on Keyfob Arm/Disarm".
•
Page 27--All references to 0722-Bit 0--"Automatic Interior Bypass" name changed to "Automatic Interior Bypass/Easy Exit".
•
Page 27--All references to 0721-Bit 7--"Enable Bell Output on Keyfob Arming" name changed to "Select Alarm Output for Keyfob Chirp".
THIS MANUAL INCLUDES FEATURES WHICH ARE ONLY AVAILABLE IN CONTROL PANEL FIRMWARE
VERSION 10 OR LATER.
NAPCO Security Systems, Inc.
333 Bayview Avenue, Amityville, New York 11701
For Sales and Repairs, call toll free: (800) 645-9445
For direct line to Technical Service, call toll free: (800) 645-9440
Internet: http://www.napcosecurity.com
IMPORTANT NOTE
This manual supports the keypad programming of the GEM-P1632 control panel with the NAPCO "classic" GEM-
RP2ASe2, GEM-RP3DGTL and GEM-RP4RFC series keypads as well as the GEM-K2AS, GEM-K3DGTL and GEM-
K4RF "K Series" keypads. The new "K Series" models offer the new STAY and AWAY buttons with simplified function-
ality, along with the new MENU and ENTER buttons. While the instructions in this manual are depicted using the "K Se-
ries" keypads, the manual applies to both the "classic" and the "K Series" keypads.
Program Mode
is the same for both keypads--
only the button names have changed
, as follows:
•
The
A
button and the
R
button operate identically (in Program Mode) for both keypads.
•
The
D
button and the
U
button operate identically (in Program Mode) for both keypads.
•
The
button and the
button operate identically (in Program Mode) for both keypads. The words
"
NEXT/YES
button" are used in this manual.
•
The
button and the
button operate identically (in Program Mode) for both keypads. The words
"
PRIOR/NO
button" are used in this manual.