X
GEM-P1632 Programming Instructions
L
NAPCO Security Systems
!
Page 18
Key Fob Transmitters
(Press
R
to set cursor).
Keyfobs can be programmed as “Arm/Disarm” devices (refer to WI752).
For each Key Fob Transmitter, enter:
!
The Key Fob Transmitter number (01–08).
!
Area number to which transmitter is assigned (1 or 2); enter 0 to disable keyfob.
!
The 6-digit RF ID # printed on the transmitter (enter all numbers and/or letters, including
leading “0”s, if any).
!
1-digit checksum number printed on the transmitter (enter all numbers and/or letters, including leading “0”s, if any).
!
Aux-1 Option (see key fob aux 1 & aux 2 options).
!
Aux-2 Option (see key fob aux 1 & aux 2 options).
Press
U
to save. Press the NEXT/YES button to proceed.
Note:
If the Key Fob is converted for Two Button “Emergency Use” (by cutting an internal jumper),
both top or bottom buttons must be depressed to activate an alarm. In this case, the Aux-1 and Aux-
2 cannot be programmed.
Key Fob Transmitters as Zone Input Devices
(refer to display above: press the PRIOR/NO button
to go backwards).
Each of the 4 key fob buttons can be assigned to a zone. For example, On button = point 1; Off
button = point 2; A1 = point 3; A2 = point 4. Up to 32 key fobs (using 1 button) or 16 key fobs (using
2 buttons) or 8 key fobs (using all 4 buttons) or any combination up to a maximum of 32 controlled
zones can be assigned, providing multiple wireless panic buttons on a system, each reporting to the
Central Station or a pager and/or annunciating on a keypad the key fob zone number with
description/location.
To assign a key fob to a zone:
program the key fob as you would a transmitter, entering the key fob's ID code,
check sum and point number at the appropriate zone. The “Quick Method” is not allowed. The zone may be hardwired to a sensor as
well as assigned to a key fob (either one will activate the zone alarm output).
NOTE:
If assigning a key fob to a zone, the “ON/OFF”
buttons on the key fob will no longer arm/disarm the system. The key fob is converted to a “panic only” device.
Dealer Code
Directly enter the Dealer Code, including leading zeros. Use the
1
through
9
buttons.
NOTE:
Press
0
for a zero. Press
U
to save.
Re-enter the Dealer Code to verify the previous code. Press
U
to save. Press the NEXT/YES but-
ton to proceed.
NOTE:
The Dealer Code can be two or more digits (up to 6 digits).
CLEAR PROGRAM:
Should it be necessary to create a new custom default program, (a) from the Dealer Program Mode, press
C
to enter the Address Program Mode; (b) access Location 1197 (Clear Program) or 1198 (Cold Start); (c) press
U
and then (d)
press
C
to exit the Dealer Program Mode. A System Trouble Condition will occur. Press
C
to silence the keypad.
NOTE: Key fobs 1-8 report openings and
closings as Users 25-32.
DATA
ENTRY
AUX 1/AUX 2
OPTIONS
0
None
1
Relay Group 1 Toggle
2
Relay Group 2 Toggle
9
Panic
A
Auxiliary
B
Instant
C
PGM2 Output Toggle
D
Access on PGM2
Output
E
Arm Stay
F
Interior Button
GEM-RP3DGTL/GEM-K3
DGTL A
N
D
GEM-RP4RFC/GEM
-K4RF Ea
s
y Me
nu Dr
iv
en Pr
ogr
am
Mode
29
INTERIOR BYPASS FIRE/TBL SYS TBL CHIME
INTERIOR BYPASS FIRE/TBL SYS TBL CHIME
KEY FOB ZONE ASSIGNMENT:
Key fobs can also be assigned to zones to allow multiple wireless panic buttons on one alarm
system, each reporting to a central station, a pager or having a description on the keypad that describes the person holding the key
fob, the location where the person holding the key fob is stationed, or the special purpose of the key fob button being depressed.
See the next page on key fob Zone Assignment.
(Direct Entry)
33
INTERIOR BYPASS FIRE/TBL SYS TBL CHIME
INTERIOR BYPASS FIRE/TBL SYS TBL CHIME
rE
ZONE DESCRIPTIONS:
GEM-K3DGTL cannot be used to enter
Zone Descriptions. To enter Zone Descriptions, you must use the
GEM-K1CA
Keypad or the Napco Quickloader Software.
DATE ENTRY:
GEM-K3DGTL cannot be used to enter
the date. To enter Date, you must use the
GEM-K1CA Keypad (Version 5 or later) or the
Napco Quickloader Software.
TIME ENTRY:
GEM-K3DGTL cannot be used to enter
the time. To enter Time, you must use the
GEM-K1CA Keypad (Version 5 or later) or the
Napco Quickloader Software.
EXIT DEALER PROGRAM MODE:
This completes the custom default program. Press
C
to enter the Direct Address Program
Mode for further programming or press
C
once again to end all programming and resume normal keypad operation.
