X
GEM-P1632 Programming Instructions
L
NAPCO Security Systems
!
Page 16
Number of Keypads
Directly enter the total number of Keypads to be installed. Valid entries are from 01 to 07. Directly
enter the number of keypads, including leading zeros. Use number buttons
1
through
9
.
NOTE:
Press
0
for a zero. Press
U
to save. Press the NEXT/YES button to proceed.
Central Station Receiver 1 Telephone Number
Using number buttons, enter telephone number of up to 16 digits including prefix letters, if
necessary, for receiver 1. Use number buttons
1
through
9
for digits 1–9; press
G
0
for a zero and
G
1
through
G
5
for letters B–F, respectively.
NOTE:
Pre-Dial Delay = “D”; Dial-Tone Detection = “E”. Pressing
0
will produce a blank space (•).
Press
U
to save. Press the NEXT/YES button to proceed.
NOTE:
Central Station Receiver 2 and
3 Telephone Numbers can only be entered in Direct Address Programming. See CS Receiver
Options.
Central Station Receiver 1 Account Number
Enter an account number of up to four digits. Use number buttons
1
through
9
for digits
1–9.
NOTE:
Press the
0
button for a zero and press the
G
0
buttons for a blank
space (•). Press
U
to save. Press the NEXT/YES button to proceed.
NOTE:
Central Station
Receiver 2 and 3 Account Numbers can only be entered in Direct Address Programming. See CS
Reporting Options.
Central Station Receiver 1 Format
From the table below, enter the central station's receiver format. Use number buttons
1
through
9
.
NOTE:
Press the
0
button for a zero and press
G
0
for a blank
space (•). Press
G
1
through
G
4
for letters B–E, respectively. Press
U
to
save. Press the NEXT/YES button to proceed.
Enter User Codes
(Press the
(
R
)
button to set cursor)
Enter up to 32 User Codes with User Options for each code. Refer to the tables below for available
data entries for User Options.
!
Press
R
once to set cursor to the User Number and enter the desired User Number. Press
R
once again to set the cursor to the User Code. Use the number buttons
1
through
9
to
enter a code from 3 to 6 digits. Enter up to 6 digits (4 digits are recommended) in the first six boxes
from left to right for each user code. Valid entries are: 0-9.
Note:
Press
0
for a zero. No blank
spaces in between; leave blank (•) any trailing boxes. If an “Ambush Prefix” (Address 0495) is entered,
do not
program the first two digits of ANY User Code as the same digits entered for the “Ambush Prefix”.
!
If the programmed code is less than 6 digits, press
R
to set the cursor to USER OPTIONS.
!
Refer to the tables on the next page for the available User Option data entries.
GEM-RP3DGTL/GEM-
K3
DGTL A
N
D
GEM-RP4RFC/GEM
-K4RF Ea
s
y Me
nu Dr
iv
en Pr
ogr
am
Mode
DATA ENTRY
CS RECEIVER 1 FORMAT
blank(•)
Ademco Slow, Silent Knight Slow
1
Sescoa, Vertex, DCI, Franklin Fast
2
Radionics Fast
3
Silent Knight Fast
4
Radionics, DCI, Franklin Slow
5
Universal High Speed
8
Radionics BFSK
DATA ENTRY
CS RECEIVER 1 FORMAT
9
FBI 4/3/1
0
Radionics Modem 2
B
SIA
C
Ademco Point ID
D
Ademco Express
E
Pager
NOTE:
Modem IIe is available
only in Direct Address
Programming. Central Station
Receiver 2 and 3 Formats can
only be entered in Direct
Address Programming. See
CS Receiver Options.
(Direct Entry)
27
INTERIOR BYPASS FIRE/TBL SYS TBL CHIME
INTERIOR BYPASS FIRE/TBL SYS TBL CHIME
(Direct Entry)
25
INTERIOR BYPASS FIRE/TBL SYS TBL CHIME
INTERIOR BYPASS FIRE/TBL SYS TBL CHIME
(Direct Entry)
22
INTERIOR BYPASS FIRE/TBL SYS TBL CHIME
INTERIOR BYPASS FIRE/TBL SYS TBL CHIME
(Direct Entry)
24
INTERIOR BYPASS FIRE/TBL SYS TBL CHIME
INTERIOR BYPASS FIRE/TBL SYS TBL CHIME
(Direct Entry)
26
INTERIOR BYPASS FIRE/TBL SYS TBL CHIME
INTERIOR BYPASS FIRE/TBL SYS TBL CHIME
8
_
H
_
3
_
3
