Muratec MFX-C3400 User Manual Download

Page: 124 / 188

Maintenance > 122

Note the positions of the four cartridges. It is essential that they go back in the same

order.

Holding the top-center of the cartridge, lift the image drum, complete with its toner

cartridge, up and out of the MFP.

Put the cartridge down gently onto a piece of paper to prevent toner from marking

your furniture and to avoid damaging the green drum surface.

With the colored toner release lever (1) to the right, pull the lever towards you. This

will release the bond between the toner cartridge and the image drum cartridge.

Lift the right-hand end of the cartridge and then draw the cartridge to the right to

release the left-hand end as shown, and withdraw the toner cartridge out of the

1. Cyan cartridge

3. Yellow cartridge

2. Magenta cartridge

4. Black cartridge

CAUTION!

The green image drum surface at the base of the cartridge is very

delicate and light sensitive. Do not touch it and do not expose it to

normal room light for more than 5 minutes. If the drum unit needs

to be out of the MFP for longer than this, please wrap the cartridge

inside a black plastic bag to keep it away from light. Never expose

the drum to direct sunlight or very bright room lighting.

Summary of Contents for MFX-C3400





























































































































































































Search results

Summary of Contents for MFX-C3400

Reviews:

Related manuals for MFX-C3400

Brands by name

Popular brands

Muratec MFX-C3400, User Manual

Search results

Summary of Contents for MFX-C3400

Reviews:

Related manuals for MFX-C3400

Brands by name

Popular brands