MR TAPCON 250 Page 98 Operating Instructions Manual Download

Page: 98 / 216

9 Operation

Maschinenfabrik Reinhausen GmbH 2022

8595028/00 EN

TAPCON

250

Figure 56: Recorder

1. Go to

Settings > Parameters > System > Recorder

2. Select the desired parameter.

3. Set the parameter.

4. Press the

Accept

button to save the modified parameter.

Average value interval

You can use this parameter to set the average value interval of the mea-
sured value recorder for electrical measured variables (current, voltage,
phase angle etc.).

9.1.8 Linking signals and events

The device allows you to link 28 digital inputs (GPI) and control system com-
mands (SCADA) with device functions, 5 digital outputs (GPO) and control
system messages.

Summary of Contents for TAPCON 250

























































































































































































































Search results

Summary of Contents for TAPCON 250

Reviews:

Related manuals for TAPCON 250

Brands by name

Popular brands

MR TAPCON 250, Operating Instructions Manual

Search results

Summary of Contents for TAPCON 250

Reviews:

Related manuals for TAPCON 250

Brands by name

Popular brands