MR TAPCON 250 Page 126 Operating Instructions Manual Download

Page: 126 / 216

9 Operation

Maschinenfabrik Reinhausen GmbH 2022

126

8595028/00 EN

TAPCON

250

If the measured value is higher than the upper limit (> or >>) or lower than
the lower limit (< or <<), the device transmits an event message.

I>>

I<<

Figure 66: Example of current monitoring with the limit value I> being exceeded

I>> Upper limit 2

I> Upper limit 1

I< Lower limit 1

I<< Lower limit 2

Delay time

Event duration

H Hysteresis

1. Go to

Settings > Parameters > Grid > Current monitoring

2. Select the desired parameter.

3. Set the desired parameter.

4. Press the

Accept

button to save the modified parameter.

You can set additional parameters for each limit value:

Mode

You can use this parameter to set which limit value you would like to use:

▪ Absolute: The device uses the absolute limit value in A/kA.

▪ Relative: The device uses the relative limit value in %, relative to the rated

current of current transformer.

Hysteresis

You can use this parameter to set the hysteresis. You can use this to avoid
the unnecessary generation of messages if the measured value fluctuates
around a threshold value.

Summary of Contents for TAPCON 250

























































































































































































































Search results

Summary of Contents for TAPCON 250

Reviews:

Related manuals for TAPCON 250

Brands by name

Popular brands

MR TAPCON 250, Operating Instructions Manual

Search results

Summary of Contents for TAPCON 250

Reviews:

Related manuals for TAPCON 250

Brands by name

Popular brands