MR TAPCON 250 Page 163 Operating Instructions Manual Download | Manualshive

Page: 163 / 216

background image

9 Operation

Maschinenfabrik Reinhausen GmbH 2022

163

8595028/00 EN

TAPCON

®

250

BCD tap position message

You can use this parameter to set which range of values from the tap posi-
tion table the device is to use for the tap position message via digital outputs
(BCD).

9.4.5 U bandwidth monitoring

The following limit values are monitored via bandwidth monitoring. The set
bandwidth of the voltage regulation is used for this purpose.

▪ Upper bandwidth

▪ Lower bandwidth

You can set the following parameters for each limit value:

▪ Hysteresis limit value: Specification as a percentage relative to the de-

sired voltage value.

▪ Delay time limit value

Behavior

If the measured value is higher than the upper limit or lower than the lower
limit, the device triggers the

Upper bandwidth limit value / Lower bandwidth

limit value

message.

The "Function monitoring" function is used to detect long periods when val-
ues are above or below the bandwidth. Long periods when values are above
or below the bandwidth indicate a problem with the device function because
the device is not able to correct the control deviation.

If the value is above or below the set bandwidth, the

Function monitoring

event is displayed after the set delay time for function monitoring has
elapsed. The event is automatically acknowledged as soon as the measured
value is back within the set bandwidth.

The following parameters are available for setting function monitoring:

▪ Function monitoring

▪ Hysteresis

▪ Delay time

▪ Monitoring U < 30 V

«
...
161
162
163
164
165
...
»

Summary of Contents for TAPCON 250

























































































































































































































Reviews:

No comments

Related manuals for TAPCON 250

Brand: H3C Pages: 57

Brand: Baader Planetarium Pages: 7

Brand: Beaphar Pages: 2

Brand: VAT Pages: 27

MorphoAccess SIGMA Extreme Series

Brand: Idemia Pages: 31

Brand: ICP DAS USA Pages: 148

Brand: ICMA Pages: 8

KOOL STRIDE KS-S

Brand: KOOL-STOP Pages: 8

GECO LUX GECO60

Brand: GiBiDi Pages: 48

Brand: East Coast Datacom Pages: 14

Brand: XtendLan Pages: 12

Brand: ZBA Pages: 27

Brand: M-system Pages: 10

Brand: Fuji Electric Pages: 12

Brand: heat-timer Pages: 36

Brand: IMG STAGELINE Pages: 14

Brand: VAT Pages: 77

Brand: WABCO Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands