Motorola GTR 8000 Manual Download | Manualshive

Page: 97 / 346

background image

3.3.9 General Electrostatic Discharge Recommendations

Total Voltage drop = [Ώ/1000 ft] x [total loop length (ft)] x [Ipeak (A)] + [connector(s) voltage drop(s)]

See

3.4.3.2 DC Power Connection Wire Gauge Calculations for Integrated Voice and Data, page 3-19

and

DC Power Connection Wire Gauge Calculations for HPD, page 3-19

for additional guidelines on cable sizing.

3.3.9 General Electrostatic Discharge Recommendations

Electronic components, such as circuit boards and memory modules, can be extremely sensitive to electrostatic
discharge (ESD). Motorola recommends that an antistatic wrist strap and a conductive foam pad be used when
installing or upgrading the system.

If an ESD station is not available, wear an antistatic wrist strap. Wrap the strap around the wrist and attach the ground
end (usually a piece of copper foil or an alligator clip) to an electrical ground. An electrical ground can be a piece of
metal that literally runs into the ground (such as an unpainted metal pipe) or the metal part of a grounded electrical
appliance. An appliance is grounded if it has a three-prong plug and is plugged into a three-prong grounded outlet.

Do not use a computer as a ground, because it is not plugged in during installation.

3.3.10 FCC Requirements

Radio frequency (RF) transmitters installed at sites within the US must be in compliance with the following FCC
regulations:

• The station licensee shall be responsible for the proper operation of the station at all times and is expected to

provide observations, servicing, and maintenance as often as may be necessary to ensure proper operation.

• The transmitter ERP shall not exceed the maximum power specified on the current station authorization.

• The frequency of the transmitter must be checked during initial installation of the transmitter, when replacing

modules, or when making adjustments that affect the carrier frequency or modulation characteristics.

This equipment has been tested and found to comply with the limits for a Class A digital device, according to part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference to radio
communications when the equipment is operated in a commercial environment.

This equipment generates, uses, and can radiate radio frequency energy. If not installed properly and used in
accordance with the instruction manuals, the equipment may cause harmful interference to radio communications.
Operation of some compliant equipment in a residential area may cause harmful interference to radio
communications, in which case the user is required to correct the interference.

3.3.11 Networking Tools

The following is a list of recommended networking tools for installing and servicing the network:

• Fluke

®

OneTouch Assistant LAN tester

• Ni-MH rechargeable battery for Fluke

• T1/E1 or E1 test set (such as the Hewlett-Packard

®

HP37702A)

• Serialtest

®

software with ComProbe

®

and SerialBERT option

6871022P86-A - November 2012

3-13

«
...
95
96
97
98
99
...
»

Summary of Contents for GTR 8000



























































































































































































































































































































































Reviews:

No comments

Related manuals for GTR 8000

Brand: Raymarine Pages: 130

Thor 1 TP9000EX

Brand: TP Radio Pages: 20

Brand: Uniden Pages: 12

Brand: Hytera Pages: 24

Musik Boy 50L RP 5240 LW

Brand: Grundig Pages: 8

Brand: Ericsson Pages: 18

Brand: KAM Pages: 6

Brand: Narco Avionics Pages: 19

Brand: B&B Electronics Pages: 60

Brand: Caliber Pages: 18

Brand: SFE Pages: 15

Brand: Entel Pages: 4

Brand: Cobra Pages: 21

MICROTALK CX105C

Brand: Cobra Pages: 1

Brand: Cobra Pages: 14

Brand: Vertex Standard Pages: 32

Brand: Bosch Pages: 44

Brand: Bosch Pages: 40

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands