Mocom millenium B2 Operating Manual Download Page 96 | Manualshive

Page: 96 / 96

Mocom millenium B2 Operating Manual Download Page 96

APPENDIX Z – TECHNICAL SUPPORT

91

APPENDIX Z – TECHNICAL SUPPORT

FOR ANY REQUEST FOR

TECHNICAL SERVICE FOR THE PRODUCT,

WHETHER IN OR OUT OF WARRANTY,

DIRECTLY CONTACT THE

TECHNICAL SUPPORT DEPARTMENT

OF THE DEALER OR RESELLER

THAT SUPPLIED THE PRODUCT.

M.O.COM. Srl is completely available to customers to provide any technical information about the product as well as to offer
suggestions and advice on steam sterilization procedures.

In this regard, please refer to the following address:

M.O.COM. Srl
Customer Support
Via delle Azalee, 1
20090 Buccinasco (MI)
ITALY
Tel. (+39)

02-45701505

Fax (+39)

02-45701258

e-mail [email protected]

website www.mocom.it

To help us in the indispensable work of improving the quality of our products and service, please send your comments
and/or suggestions to the following e-mail address:

[email protected]

(Commercial /Sales Department)

Or, you can send a letter or fax to the above address.

Thank you in advance for your valuable assistance.

«
...
94
95
96

Summary of Contents for millenium B2

































































































Reviews:

No comments