© Mitsubishi Forklift Trucks 2013. All
© Mitsubishi Forklift Trucks 2013. All
rights reserved.
rights reserved.
Revision: B
Revision: B
Document ID: 615023
Document ID: 615023
170 (244)
170 (244)
PBV20N2
PBV20N2
Service
Service Manual
Manual
CODE
CODE
TRUCKTOOL
TRUCKTOOL
AND
AND
DISPLAY
DISPLAY
DESCRIPTION
DESCRIPTION
243
243
Error in pump command value range
Error in pump command value range
PUMP VACC RANGE
PUMP VACC RANGE
(Alarm)
(Alarm)
This alarm indicates that the lift lever voltage is out of range.
This alarm indicates that the lift lever voltage is out of range.
In such a case, check the following:
In such a case, check the following:
•
•
Teach the lift lever values again.
Teach the lift lever values again.
•
•
Check that the connectors and cables are in order.
Check that the connectors and cables are in order.
•
•
Replace the lift lever and t
Replace the lift lever and teach the new values.
each the new values.
245
245
Error in the pump command value
Error in the pump command value
PUMP VACC NOT OK
PUMP VACC NOT OK
(Alarm)
(Alarm)
This alarm occurs when the lift lever output
This alarm occurs when the lift lever output voltage differs from the values acquired at
voltage differs from the values acquired at
calibration.
calibration.
In such a case, check the functionality of
In such a case, check the functionality of the lift lever. Perform the
the lift lever. Perform the lift lever calibration wizard
lift lever calibration wizard
function.
function.
246
246
Error in magnetic brake driver error
Error in magnetic brake driver error
AUX DRIV. OPEN
AUX DRIV. OPEN
(Alarm)
Stored
(Alarm)
Stored
This alarm indicates that the driver of
This alarm indicates that the driver of the electromagnetic brake coil is not able
the electromagnetic brake coil is not able to drive the
to drive the
load.
load.
The driver inside the COMBIACX controller is damaged, so the controller has
The driver inside the COMBIACX controller is damaged, so the controller has to be replaced.
to be replaced.
247
247
Acquisition of gain values
Acquisition of gain values
DATA ACQUISITION
DATA ACQUISITION
(Warning)
(Warning)
This warning indicates acquisition of the current gains.
This warning indicates acquisition of the current gains.
The warning disappears when the acquisition is
The warning disappears when the acquisition is done. This alarm is a part
done. This alarm is a part of normal operation
of normal operation
of the controller.
of the controller.
248
248
Curtis display not present
Curtis display not present
NO CAN MSG.
NO CAN MSG.
(Alarm)
Stored
(Alarm)
Stored
This alarm is displayed where there is no
This alarm is displayed where there is no CAN message from the Curtis display.
CAN message from the Curtis display.
This alarm can be caused by a
This alarm can be caused by a CAN bus malfunction, which blinds the traction-display
CAN bus malfunction, which blinds the traction-display
communication. If not, it is an
communication. If not, it is an internal problem in the COMBIACX controller or in the
internal problem in the COMBIACX controller or in the Curtis
Curtis
display.
display.
249
249
Call for programmed maintenance
Call for programmed maintenance
CHECK UP NEEDED
CHECK UP NEEDED
(Warning)
(Warning)
This is just a
This is just a warning calling for programmed maintenance.
warning calling for programmed maintenance.
Set the CHECK UP DONE parameter to the ON value after
Set the CHECK UP DONE parameter to the ON value after the maintenance is carried out.
the maintenance is carried out.
250
250
Controller thermal sensor failure
Controller thermal sensor failure
THERMIC SENS. KO
THERMIC SENS. KO
(Warning)
Stored
(Warning)
Stored
This warning indicates that the output of the controller thermal sensor is out of range.
This warning indicates that the output of the controller thermal sensor is out of range.
This fault is not
This fault is not related to external components, so when it appears, replace the
related to external components, so when it appears, replace the COMBIACX
COMBIACX
controller.
controller.
https://www.forkliftpdfmanuals.com/
