Mitsubishi Electric FR-A800 Installation Manuallines Download

Page: 62 / 68

A APPENDIX

A.1 Instructions for Compliance with the EU Directives

The EU Directives are issued to standardize different national regulations of the EU Member States and to facilitate free
movement of the equipment, whose safety is ensured, in the EU territory.

Since 1996, compliance with the EMC Directive that is one of the EU Directives has been legally required. Since 1997,
compliance with the Low Voltage Directive, another EU Directive, has been also legally required. When a manufacturer
confirms its equipment to be compliant with the EMC Directive and the Low Voltage Directive, the manufacturer must
declare the conformity and affix the CE marking.

The authorized representative in the EU
Name: Mitsubishi Electric Europe B.V.
Address: Gothaer Straße 8, 40880 Ratingen, Germany

A.1.1 EMC Directive

We declare that this inverter conforms with the EMC Directive and affix the CE marking on the inverter.

EMC Directive: 2004/108/EC

Standard(s): EN61800-3:2004 (Second environment / PDS Category "C3")
Standards for IP55 compatible models: EN61800-3:2004 (First environment / PDS Category "C2",
Second environment / PDS Category "C3". The applicable standard depends on the built-in EMC filter.)

This inverter is not intended to be used on a low-voltage public network which supplies domestic premises.

Radio frequency interference is expected if used on such a network.

The installer shall provide a guide for installation and use, including recommended mitigation devices.

NOTE

We declare that this inverter conforms with the EMC Directive in industrial environments and affix the CE marking on
the inverter. When using the inverter in a residential area, take appropriate measures and ensure the conformity of the
inverter used in the residential area.

NOTES

First environment
Environment including residential buildings. Includes buildings directly connected without a transformer to the low
voltage power supply network which supplies power to residential buildings.

Second environment
Environment including all buildings except buildings directly connected without a transformer to the low voltage
power supply network which supplies power to residential buildings.

NOTES

Set the EMC filter valid and install the inverter and perform wiring according to the following instructions:

The inverter (resp. the converter unit for separated converter types) is equipped with a built-in EMC filter. Set the
EMC filter valid. (For details, refer to the FR-A800 and FR-CC2 Instruction Manuals.)

Connect the inverter (and the converter unit) to an earthed power supply.

Install a motor and a control cable according to the EMC Installation Guidelines (BCN-A21041-204).

The cable length between the inverter and the motor is 5 m maximum.

Confirm that the inverter (and the converter unit) conforms with the EMC Directive as the industrial drives application
for final installation.

For IP55 compatible models:
If the inverter with a built-in Class C2 EMC filter has an input current of 16 A or less, limits for harmonic current
emissions of EN/IEC61000-3-2 shall apply.
However, if the inverter is the professional equipment with a total rated power of 1 kW or higher, limits for harmonic
current emissions of EN/IEC61000-3-2 shall not apply. If the equipment input current is more than 16 A and does not
exceed 75 A, the equipment complies with EN/IEC61000-3-12 provided that the short-circuit power Ssc is greater
than or equal to the value provided in the table below at the interface point between the user's supply and the public
system. It is the responsibility of the installer or user of the equipment to ensure, by consultation with the distribution
network operator if necessary, that the equipment is connected only to a supply with a short-circuit power Ssc greater
than or equal to the value mentioned in the table below.

Inverter model

Standard

Ssc

Rsce

FR-A846-00023(0.4K)

EN/IEC61000-3-2

—

FR-A846-00250(7.5K)

EN/IEC61000-3-12

2261 kVA

≥

120