Mitsubishi Electric AE-200A Instruction Book Download Page 57

Page: 57 / 192

WT07996X02

Item

Description

File format

Row

Item

Date

range

Format

4th

Measurement item

The format of the display target and comparison target to be output is as

follows.

■

Address

“Address” + “-” + AE No.

+ “-” + Address “-” + Display item (Bar/

Line)

“Address” + “-” + AE No.

+ “-” + Address “-” + Metering device No.

+ “-” + Display item (Bar)

<Built-in Pulse Input (PI)>

“Pulse input” + “-” + AE No.

+ “-” + Channel No. + “-” + Display item (Bar)

“Address” + “-” + AE No.

+ “-” + Address “-” + Sensor No. + “-” +

Display item (Line)

■

Group

Group name

+ “-” + Display item (Bar/Line)

■

Block

Block name

+ “-” + Display item (Bar/Line)

■

Energy management block

Energy management block name

+ “-” + Display item (Bar/Line)

5th–

Data

Day

hh:mm,

Data value (Bar), Comparison data value (Bar), Target electric

energy value

, Data value (Line), Comparison data value

(Line)

Month

dd,

Year

mm,

*1 “Target electric energy(kWh)” and the target electric energy value will appear only when the data is displayed in

the graph.

*2 If the group name has not been registered, [“Group” + AE No. + “-” + Group number] will appear. If the block name

has not been registered, [“Block” + AE No. + “-” + Block number] will appear. If the energy management block

name has not been registered, [“Energy mgmt block” + AE No. + “-” + Energy management block number] will

appear.

*3 For AE No., refer to 4 “Name Display” in Chapter 1.
*4 The number of rows varies with the selected date range. (Day: 5th–52nd; Month: 5th–35th; Year: 5th–16th)

File sample

(Display

range: Block)

Date range: Year

413

2015:2014

Administration Dpt./Block01-1-03

Month,Administration Dpt. - Indoor Unit Electric Energy[kWh],Block01-1-03 - Indoor Unit Electric Energy[kWh],Target

electric energy[kWh],Administration Dpt. - Outdoor Temp.[ºC],Block01-1-03 - Outdoor Temp.[ºC]

1,675.17,661.93,600,0.4,0.5

2,697.38,683.71,700,0.3,3.2

3,528.63,518.26,400,4.5,3.8

Date range: Month

412

2015/04:2014/04

Administration Dpt./Block01-1-03

Day,Administration Dpt. - Indoor Unit Electric Energy[kWh],Block01-1-03 - Indoor Unit Electric Energy[kWh],Target electric

energy[kWh],Administration Dpt. - Outdoor Temp.[ºC],Block01-1-03 - Outdoor Temp.[ºC]

1,24.69,8.74,22,26.2,17.9

2,25.31,8.22,22,27,17.4

3,12.36,22.33,10,25.2,16.6

Date range: Day

411

2015/08/19:2014/06/01

Administration Dpt./Block01-1-03

Time,Administration Dpt. - Indoor Unit Electric Energy[kWh],Block01-1-03 - Indoor Unit Electric Energy[kWh],Administration

Dpt. - Outdoor Temp.[ºC],Block01-1-03 - Outdoor Temp.[ºC]

0:00,0.61,0.25,23.2,17.8

1:00,0.65,0.51,23.1,17.6

2:00,0.66,0.48,22.1,18.1

For building managers

Chapter 2

Summary of Contents for AE-200A

































































































































































































Search results

Summary of Contents for AE-200A

Reviews:

Brands by name

Popular brands

Mitsubishi Electric AE-200A, Instruction Book

Search results

Summary of Contents for AE-200A

Reviews:

Brands by name

Popular brands