manualshive.com logo in svg

Mitsubishi Electric AE-200A, Instruction Book

Share
Download
Mitsubishi Electric AE-200A Instruction Book Download Page 116

116

WT07996X02

1-1-5. Advanced settings

In the group list, selecting the group icon(s) and clicking [Advanced] in the taskbar will bring up the operation 

settings screen for the selected group(s). The current operation status will appear.

Change necessary operation settings, and then click [Send] to reflect the changes. Click [Close] to return to the 

previous screen without making any changes.

 

    Note:  When the setting is changed from other controllers, the operation status shown on the screen will not be updated while the 

screen is open.

[1]  Air conditioning unit group

 

 

Item

Operation method

Description

ON/OFF

Select [ON] or 

[OFF].

Turns on or off the units.

Operation 

mode

Select an operation 

mode.

Click the desired operation mode.

[Cool], [Dry], [Fan], [Heat], [Auto], [Setback]

 

Note:  When the operation mode signals from the cooling/heating switchover model of 

units are mixed (Cool and Heat), the operation mode will not change.

 

Note:  The Setback mode can be selected on the AE-200A/AE-50A/EW-50A, but not 

on the AE-200E/AE-50E/EW-50E.

Set 

temperature

Adjust the set 

temperature with 
the 

 

 

buttons.

Depending on settings values resulting from restrictions by device functions and 

set temperature range restriction functions, temperature settings ranges may be 

restricted.

 

Note:  For the same indoor unit, when changing operation mode and set temperature 

from multiple operation devices (system controllers, remote controllers), display 

of outside the allowable settings range may occur.

 

Note:  Depending on the unit model, setting in 0.5°C units and 1°C units is possible.

 

Note:  If the indoor unit supports the dual-set-point function in the Auto mode and 

when the operation mode above is set to Auto or Setback, two set temperatures 

for Cool mode and Heat mode can be set. For details about the dual-set-point 

function, refer to page 118.

 

Note:  When the indoor units that support the dual-set-point function and the indoor 

units that do not support the dual-set-point function exist in the same group, 

only one set temperature can be set in the Auto mode.

Air Direction

Adjust the air 

direction with the 

 

 

buttons.

Auto

Swing

Fan Speed

Adjust the fan speed 
with the 

 

 buttons.

Auto

Interlocked 

LOSSNAY  

ON/OFF

Select [ON] or 

[OFF].

Turns on or off the interlocked LOSSNAY units (ventilator).

Set temperature

Close

Click to close the settings 

screen without making any 

changes.

Send

Click to reflect 

the changes 

made.

Close

Click to close the settings 

screen without making any 

changes.

Fan Speed

Filter Sign Reset

Click to reset the 

filter sign.

Send

Click to reflect the 

changes made.

Group name

ON/OFF

Operation 

mode

Air Direction

Interlocked 

LOSSNAY  

ON/OFF

Fan speed of 

interlocked 

LOSSNAY

Hold

Schedule

Prohibit Remote 

Controller Operation

Summary of Contents for AE-200A

































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands