manualshive.com logo in svg

Mitsubishi Electric AE-200A, Instruction Book

Share
Download
Mitsubishi Electric AE-200A Instruction Book Download Page 170

170

WT07996X02

Item

Description

ON/OFF

Touch [ON] or [OFF] to turn on or off the units.

 

Note:  Switching this setting will turn on or off the LOSSNAY unit as well that is interlocked with the 

operation of indoor units in the group. To turn on or off the LOSSNAY unit only, use the “Interlocked 

LOSSNAY ON/OFF” switch.

Operation mode

Touch   to display the operation mode selection screen, and select the desired operation mode.
Touch   to return to the operation settings screen.

 

Note:  The Setback mode can be selected on the AE-200A/AE-50A/EW-50A, but not on the 

AE-200E/AE-50E/EW-50E.

Set temperature

Touch 

 or 

 to change the set temperature.

Depending on settings values resulting from restrictions by device functions and set temperature range 

restriction functions, temperature settings ranges may be restricted.

 

Note:  Depending on the unit model, setting in 0.5°C units and 1°C units is possible.

 

Note:  If the indoor unit supports the dual-set-point function and when the operation mode above is set to 

Auto or Setback, two set temperatures for Cool mode and Heat mode can be set.

Air Direction

Touch 

 or 

 to adjust the air direction.

Auto

Swing

Fan Speed

Touch 

 or 

 to adjust the fan speed.

Auto

Filter Sign Reset

Click 

 to switch between resetting and not resetting the filter sign.

To reset, display a checkmark ( 

 ).

 

Note:  If a filter sign in the group has not been triggered, then this item will not appear.

Interlocked 

LOSSNAY ON/

OFF

Touch [ON] or [OFF] to turn on or off the interlocked LOSSNAY units (ventilator).

 

Note:  For a group that is not connected to an interlocked LOSSNAY unit (ventilator), this item will not 

appear.

Fan speed of 

interlocked 

LOSSNAY

Touch 

 or 

 to adjust the fan speed of the interlocked LOSSNAY units (ventilator).

 

Note:  For a group that is not connected to an interlocked LOSSNAY unit (ventilator), this item will not 

appear.

Other operation 

status information

Operation status other than the operation items will appear.

Operation 

prohibition mark

Operation prohibition mark 

 is displayed on the operation items that are prohibited from the local 

remote controllers.

 is displayed when one or more operation items are prohibited.

Send

Touch   to reflect the changes and return to the group list.

Cancel

Touch   to return to the group list without sending any changes.

Summary of Contents for AE-200A

































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands