Mircom DTC-300A Installation And Operation Manual Download Page 35

Page: 35 / 40

12.0

Compatible Fire Alarm Control

Panels

Mircom DTC-300A:

Compatible with

Mircom FA-300 Series, FX-2000 Series and FA-1000

Series

Fire Alarm Control Panels and all other FACP that can provide 24V DC regulated or

24V DC FWR power, 60mA current MIN and 110mA MAX and normally open relay contacts
rated 28V DC, 2A resistive load.

13.0

Compatible Receivers

The

Mircom DTC-300A

is compatible with the following

Digital Alarm Communicator

Receivers (DACR):

14.0

Specifications

All Circuits are Power Limited except 24V DC OUT

DTC-300A Digital Communicator

•

Connects to two Telephone Lines and performs line supervision.

•

Connects to a FACP via input zones and 24V DC regulated or 24V DC FWR power.

•

Transmits user configurable Alarm, Supervisory, and Trouble status to a DACR, using
either Ademco Contact ID or SIA DCS protocols.

•

User configurable locally or remotely. Configuration is passcode protected.

•

Current Consumption:

Standby

: 60 mA

Alarm

: 110 mA

15.0

Battery Calculations

The DTC-300A Battery Calculations are performed as part of the calculations for the Fire
Alarm Control Panel it will be used in. See the appropriate Mircom Installation and Operation
Manual.

DACR Receiver Model

Protocols

SurGard MLR2 Multi-Line Receiver (ULC, ULI Approved)

SIA-DCS and Ademco Contact ID

SurGard SLR Single-Line Receiver (ULC, ULI Approved)

SIA-DCS and Ademco Contact ID

Osborne-Hoffman Quickalert! II Receiver (ULI Approved)

SIA-DCS and Ademco Contact ID

Osborne-Hoffman OH-2000 Receiver (ULI Approved)

SIA-DCS and Ademco Contact ID

Silent Knight Model 9500 Receiver (ULI Approved)

SIA-DCS and Ademco Contact ID

Radionics Model D6500 Receiver (ULI Approved)

Ademco Contact ID

Radionics Model D6600 Receiver (ULI Approved)

SIA-DCS and Ademco Contact ID

Summary of Contents for DTC-300A









































Search results

Summary of Contents for DTC-300A

Reviews:

Related manuals for DTC-300A

Brands by name

Popular brands

Mircom DTC-300A, Installation And Operation Manual

Search results

Summary of Contents for DTC-300A

Reviews:

Related manuals for DTC-300A

Brands by name

Popular brands