manualshive.com logo in svg

MINOLTA-QMS MAGICOLOR 6110, User Manual

Share
Download
MINOLTA-QMS MAGICOLOR 6110 User Manual Download Page 97

Solving Problems with Printing Quality 

95

Vertical 
streaking 
appears.

The laser lens cover 
may be dirty.

Check to see if the laser lens cover is dirty. If 
necessary, clean it with a clean soft cloth.

The corona wire inside 
the OPC belt cartridge 
may be dirty. 

Clean the corona wire.

One or more toner car-
tridges may be defec-
tive.

The item may be defective or misinstalled. 
Remove the item, check it for damage, and 
reinstall it. If necessary, replace it. 

The OPC belt cartridge 
may be defective or 
misinstalled.

The fuser unit may be 
defective or misin-
stalled.

The transfer unit may 
be defective or misin-
stalled.

If a wide vertical white 
band appears, check 
the transfer drum sur-
face. 

Clean the transfer drum surface. If necessary

, 

clean the oil off the surface.

Make sure that the transfer unit is closed.

Symptom

Cause

Solution

Summary of Contents for MAGICOLOR 6110

























































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands