manualshive.com logo in svg

MINOLTA-QMS MAGICOLOR 6110, User Manual

Share
Download
MINOLTA-QMS MAGICOLOR 6110 User Manual Download Page 135

Lower Feeder Unit (LFU) 

133

Kit Contents

„

Lower feeder unit (LFU)

„

Universal media tray (500 sheets)

„

One small metal bracket with thumb-
screw (attached to the LFU)

„

Two plastic side covers (one left and 
one right) 

5

"

There may be other pieces shipped 
with the LFU; however, they are not 
required for this procedure.

Installation

WARNING!

Your printer weighs approximately 112 lbs (51 kg) with consumables. Be 
sure to have help when lifting and moving it. 

ACHTUNG! Das Gewicht dieses Druckers beträgt mit 
Verbrauchsmaterial ca. 51 kg. Bitte versuchen Sie niemals, den Drucker 
alleine anzuheben oder zu transportieren.

Attention

Never lift a printer with the fuser oil bottle installed. If other 
consumables are installed, be sure to keep the printer level when 
moving it to prevent accidental spills. 

Summary of Contents for MAGICOLOR 6110

























































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands