manualshive.com logo in svg

MINOLTA-QMS MAGICOLOR 6110, User Manual

Share
Download
MINOLTA-QMS MAGICOLOR 6110 User Manual Download Page 20

Replacing the OPC Belt Cartridge

18

2

Rotate up the two lock 
levers (one on each 
side of the OPC belt 
cartridge). 

3

Remove the used 
OPC belt 
cartridge.

WARNING!

Dispose of the used OPC belt cartridge according to your local 
regulations. Do not dispose of it by burning.

ACHTUNG! Entsorgen Sie die Trommeleinheit ordnungsgemäß 
entsprechend den lokalen Bestimmungen.

4

Remove the new OPC belt cartridge from its packaging.

5

Pull out the two 
orange tension- 
release pins A 
(one on each 
side of the 
cartridge), and 
then remove the 
protective 
sheet B from 
the cartridge.

5

"

The green surface of the cartridge faces you. The white powder 
lubricant on a new OPC belt is normal; it won’t affect quality.

A

A

B

Summary of Contents for MAGICOLOR 6110

























































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands