manualshive.com logo in svg

MINOLTA-QMS MAGICOLOR 6110, User Manual

Share
Download
MINOLTA-QMS MAGICOLOR 6110 User Manual Download Page 34

Printing Area

32

Media Trays

Printing Area

What sizes of media can I use?

Your printer supports full-color printing on all media sizes. Each media size 
has a specific imageable area, the maximum area on which the printer can 
print clearly and without distortion. This area is subject to both hardware limits 
(the physical media size and the margins required by the printer) and soft-
ware constraints (the amount of memory available for the full-page frame 
buffer). The imageable (printable) area for media sizes except oversize is the 
page size minus 0.197" (5 mm) from the edges. The imageable (printable) 
area for oversize media left and right edges is the page size minus 0.393" 
(10 mm).

Location

Media tray

Sheet capacity

Upper 

Universal (standard) Tray 1

250 

Upper 

Letter/A4 (optional) (replaces the 
universal tray)

250 

Lower

Lower feeder unit (LFU) (up to two 
optional) Trays 2 and 3

500 each

Notes

You may rename these trays for your convenience. See the 
CrownBook for more information.

Summary of Contents for MAGICOLOR 6110

























































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands