manualshive.com logo in svg

MINOLTA-QMS MAGICOLOR 6110, User Manual

Share
Download
MINOLTA-QMS MAGICOLOR 6110 User Manual Download Page 29

Replacing the Ozone Filter 

27

6

In the Operator Control/Consumables/Item Replaced/Waste Toner Bottle 
menu choose Yes to reset the consumables monitoring system.

5

"

When you replace the waste toner bottle after a  

CHECK WASTE 

TONER 

message displays in the message window, the engine 

automatically recovers. However, you should manually reset the 
consumables usage monitoring system to ensure accurate con-
sumables monitoring.

To access consumables usage information, use the Operator Control/
Consumables/Print Statistics menu or the CrownView printer web page.

Replacing the Ozone Filter 

How do I replace the ozone filter?

The ozone filter reduces exhausted ozone gas. It should be replaced every 
12 months.

1

Slide open the ozone filter door on 
the left rear of the printer.

2

Remove the ozone filter from 
the case.

5

"

Dispose of the used ozone 
filter according to your local 
regulations.

3

Install a new ozone filter 
in the case.

4

Reinstall the ozone filter 
case.

B

A

B

A

B

Summary of Contents for MAGICOLOR 6110

























































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands