manualshive.com logo in svg

MINOLTA-QMS MAGICOLOR 6110, User Manual

Share
Download
MINOLTA-QMS MAGICOLOR 6110 User Manual Download Page 67

Maintenance Schedule 

65

„

Never use sharp or rough implements, such as wire or plastic cleaning 
pads.

„

Never spray a cleaning solution directly on the printer as the cleaning 
solution will penetrate to the interior of the printer and cause damage.

Maintenance Schedule

Preventive Maintenance Schedule

Replacement Schedule

Printer needs 
preventive 
maintenance 
after...

When...

By...

30,000 pages

30K MAINTENANCE 

displays in the 

message window.

User

See “Cleaning Schedule” 
on page 54.

240,000 pages

240K MAINTENANCE 

displays in the 

message window.

120,000 pages

120K CHECKUP 

displays in the mes-

sage window.

This item 
needs 
replacing...

After...

By...

Cleaning roller

REPLACE FUSER CLEANER 

displays 

in the message window (after 20,000 
pages at 5% coverage of each color).

User

See “Replacing the Fuser 
Oil Bottle and Cleaning 
Roller.”

Fuser oil bottle

CHECK CLEANING ROLLER 

displays 

in the message window (after approxi-
mately 12,000 pages; however, fuser 
oil bottle life is media dependent—
coarser paper requires more oil).

User

See “Replacing the Fuser 
Oil Bottle and Cleaning 
Roller.”

Summary of Contents for MAGICOLOR 6110

























































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands