Minebea Intec Maxxis 4 Installation Manual Download Page 83

Page: 83 / 112

Technical data

Description

Data

Internal connection

Pin strip, 50

‑

External connection

‑

pin D

‑

Sub female connector in module cover

Transfer rate

9.6 kbit/s to 12 Mbit/s, baud rate auto-detection

Connection mode

ProiBus network,

connections can be made/released without afecting other

stations.

Protocol

PROFIBUS-DP-V0 SLAVE to IEC 61158

Coniguration

GSD ile

"SART_5500.gsd"

Potential isolation

Yes, optocoupler in lines A and B (RS-485)

Bus termination

The bus termination in the last device is implemented via the

integrated terminating resistor in the ProiBus plug.

Cable type

ProiBus "special"; color: violet; screened twisted pair cable

Cable impedance

150

Ω

Cable length

The max. distance of 200 m can be extended at 1.5 Mbit/s by

means of an additional repeater.

Dimensions (LxWxH)

55x50x22 mm

Weight

Approx. 33 g

Certiicates

Proibus test center Comdec in Germany and PNO (Proibus

User Organization).

Industry-compatible CE, UL, and cUL

Note:

The GSD ile is stored on the CD supplied with the device (ieldbus directory of the

respective device). The current ile is also available to download online:
http://www.minebea-intec.com

4 Device installation

Process Controller Maxxis 4 PR 5500

Minebea Intec

EN-81

Summary of Contents for Maxxis 4

















































































































Search results

Summary of Contents for Maxxis 4

Reviews:

Related manuals for Maxxis 4

Brands by name

Popular brands

Minebea Intec Maxxis 4, Installation Manual

Search results

Summary of Contents for Maxxis 4

Reviews:

Related manuals for Maxxis 4

Brands by name

Popular brands