Minebea Intec Maxxis 4 Installation Manual Download Page 110

Page: 110 / 112

Fast transient disturbances (Burst)

EN 61000-4-4

2 kV

Peak voltages (surge) 1.2/50 µs

EN 61000-4-5

1/2 V

Conducted disturbances by high fre-

quency coupling (0.15…80 MHz)

EN 61000-4-6

10 V

Voltage dips

EN 61000-4-11

0/40/70%

20/200/500ms

Mains inputs

Mains failure link

EN 61000-4-11

20 ms

7.4.3

RF interference suppression

Interference emission

EN 55011, Group 1, Limit class A, for industrial

sectors

7.5 Mechanics

7.5.1

Design

Control cabinet housing made of stainless steel and aluminum, protection class IP65, rear

IP20.

7.5.2

Dimensions

Width

186/192/199 mm

Height

90/96/103 mm

Depth

approx. 203 mm (incl. screen clamping rail)

7.5.3

Weights

Net weight

2.2 kg

Shipping weight

3.1 kg

7.6 Use in legal metrology

7.6.1

Documentation relating to calibration on the CD included

The documents and manuals listed in the appendix (see Chapter

8.1

) can be found on the

PR 5500 CD.

7.6.2

Further information

For information about the signiicance of the CAL switch to be sealed, see Chapter

4.4.1

and [Commissioning] - [Overwrite protection] - [CAL switch] in the PR 5500 operating

manual.
Ensure that the parameter settings (see [System setup] - [Weighing points] - [Internal

weighing point] - [Parameters] in the PR 5500 operating manual) selected comply with

the legal requirements as well as the provisions of EC type approval certiication.
The party installing the scale is responsible for selecting legally permissible settings.

These settings need to be checked.

Process Controller Maxxis 4 PR 5500

7 Technical data

EN-108

Minebea Intec

Summary of Contents for Maxxis 4

















































































































Search results

Summary of Contents for Maxxis 4

Reviews:

Related manuals for Maxxis 4

Brands by name

Popular brands

Minebea Intec Maxxis 4, Installation Manual

Search results

Summary of Contents for Maxxis 4

Reviews:

Related manuals for Maxxis 4

Brands by name

Popular brands