6
OPERATION
WARNING
To reduce the risk of injury, always
wear safety goggles or glasses
with side shields.
Using Forward/Reverse Switch
1. For
forward
(clockwise)
Forward
Trigger
Reverse
Switch
Front of Tool
rotation, push the for-
ward/reverse switch to
the left position as
shown.
2. For
reverse
(coun-
terclockwise) rotation,
push the forward/re
-
verse switch to the
right position as shown.
Although an interlock
prevents reversing the
tool while the motor
is running, allow it to
come to a full stop be-
fore reversing.
WARNING
To reduce the risk of injury, keep
hands and cord away from the bit
and all moving parts.
Starting, Stopping and Controlling Speed
1. To
start
the tool, pull the trigger.
2. To
stop
the tool, release the trigger.
3. To
vary
the drilling speed, simply increase or
decrease pressure on the trigger. The further the
trigger is pulled, the greater the speed.
Locking Trigger
The lock button holds the trigger in the ON position
for continuous full speed use.
1. To
lock
the trigger, hold the lock button in while
pulling the trigger. Release the trigger.
2. To
unlock
the trigger, pull the trigger and release.
The lock button will pop out.
NR = Not recommended
WARNING
To reduce the risk of explosion,
electric shock and property dam-
age, always check the work area for hidden pipes
and wires before drilling.
Selecting Bits
When selecting a bit, use the right type for your job.
For best performance, always use sharp bits.
Drilling
1. Before drilling, be sure the workpiece is clamped
securely. Use backing material to prevent damage
to the workpiece during breakthrough.
2. When starting a hole, place the drill bit on the work
surface and apply firm pressure. Begin drilling at
a slow speed, gradually increasing the speed as
you drill.
3. Always apply pressure in line with the bit. Use
enough pressure to keep the drill biting, but do
not push hard enough to stall the motor.
4. Reduce pressure and ease the bit through the last
part of the hole. While the tool is still running, pull
the bit out of the hole to prevent jamming.
Drilling in Wood, Composition Materials
and Plastic
When drilling in wood, composition materials and
plastic, start the drill slowly, gradually increasing
speed as you drill. When using twist drill bits, pull
the bit out of the hole frequently to clear chips from
the bit flutes. Use low speeds for plastics with a low
melting point.
Drilling in Masonry
When drilling in masonry, use high speed carbide-
tipped bits. Drilling soft masonry materials such as
cinder block requires little pressure. Hard materials
like concrete require more pressure. A smooth, even
flow of dust indicates the proper drilling rate. Do not
let the bit spin in the hole without cutting. Do not use
water to settle dust or to cool bit. Both actions will
damage the carbide.
Drilling in Metal
When drilling in metal, use high speed steel twist drills
or hole saws. Use slow speeds for hard metals and
high speeds for softer metals. Lubricate drill bits with
cutting oil when drilling in iron or steel. Use a coolant
when drilling in nonferrous metals such as copper,
brass or aluminum. Back the material to prevent
binding and distortion on breakthrough.
Driving Screws
When driving screws, use the proper screwdriver bit
for your job. After drilling pilot and shank holes, start
the screw slowly and increase the speed as driving
progresses. Set the screw by slowing to a stop. Do
not run screws down at excessive speeds. To remove
screws, reverse the motor.
Wood
Wood/Steel
Steel
Cat. No.
No Load
RPM
Flat Boring
Bits
Auger
Bits
Hole
Saws
Self-feed
Bits
Pathfinder
TM
Bits
Twist
Bits
Hole
Saws
0100-20
0101-20
0200-20
0201-20
0202-20
0299-20
0300-20
0302-20
0 - 2500
0 - 4300
0 - 1200
0 - 2500
0 - 1200
0 - 850
0 - 850
0 - 850
1-1/2"
1-1/4"
1-1/2"
1-1/2"
1-1/2"
1-1/2"
1-1/2"
1-1/2"
NR
NR
1"
7/8"
1"
1-1/2"
1-1/2"
1-1/2"
NR
NR
3-1/4"
2-1/4"
3-1/4"
3-5/8"
3-5/8"
3-5/8"
NR
NR
NR
NR
NR
2-9/16"
2-9/16"
2-9/16"
NR
NR
1-1/4"
1-1/4"
1-1/4"
1-1/4"
1-1/4"
1-1/4"
1/4"
1/4"
1/2"
1/2"
1/2"
3/4"
3/4"
3/4"
NR
NR
1-5/8"
NR
1-5/8"
2"
2"
2"
APPLICATIONS
