Miele PW 5082 Operating And Installation Instructions Download Page 52 | Manualshive

Page: 52 / 68

background image

Levelling the machine

Ensure that the machine feet and the
floor are dry to prevent the machine
from slipping during the spin cycle.

,

The machine must stand

perfectly level on all four feet to
ensure safe and proper operation.

Incorrect installation may increase
electricity and water consumption and
may cause the machine to move about.

Screwing out and adjusting the feet

The four adjustable screw feet are used
to level the machine. All four feet are
screwed in when the machine is
delivered.

^

Using the spanner supplied, turn
counter nut

2

in a clockwise

direction. Then turn counter nut

2

together with foot

1

to unscrew.

^

Use a spirit level to check the
machine is standing level.

^

Hold foot

1

securely with a pipe

wrench. Turn counter nut

2

again

using the spanner supplied until it
sits firmly up against the housing.

,

All four counter nuts must sit

firmly up against the housing. Please
also check this for the feet which did
not need adjustment. Otherwise
there is the danger of the machine
moving about.

Installation

52

«
...
50
51
52
53
54
...
»

Summary of Contents for PW 5082





































































Reviews:

No comments

Related manuals for PW 5082

Brand: saco Pages: 5

Brand: VOX electronics Pages: 154

Brand: LASA Pages: 60

Brand: Parker Pages: 17

Brand: Kärcher Pages: 90

Brand: Power Stroke Pages: 44

Brand: Asko Pages: 2

Brand: Heinner Pages: 58

Brand: Hotpoint Pages: 16

Brand: ETNA Pages: 72

Brand: Sammic Pages: 32

Brand: Hisense Pages: 72

Brand: Progress Pages: 48

Brand: UNITED Pages: 32

Brand: ECG Pages: 188

Brand: Samsung Pages: 52

WW60J426 Series

Brand: Samsung Pages: 56

Brand: Samsung Pages: 60

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands