Miele PW 5082 Operating And Installation Instructions Download Page 51 | Manualshive

Page: 51 / 68

background image

^

Release the catch and turn the right
hand transit bar anti-clockwise by
90°.

^

Then withdraw the transit bar.

,

To avoid the risk of injury the

holes for the transit bars must be
covered after they have been
removed. If they are not covered
there is a risk of injury.

^

Plug the holes with the plastic caps
supplied.

,

The machine must not be moved

without the transit bars in place.
Store them as shown or keep them
in a safe place for future use. They
must be re-fitted if the machine is to
be moved again (e.g. when moving
house).

,

When moving the machine make

sure it is stable.

Re-fitting the transit bars

Re-fitting is carried out by reversing the
procedure.

Installation

51

«
...
49
50
51
52
53
...
»

Summary of Contents for PW 5082





































































Reviews:

No comments

Related manuals for PW 5082

Brand: Danby Pages: 42

Brand: Danby Pages: 11

Brand: Danby Pages: 10

Brand: Samsung Pages: 132

Brand: GE Pages: 78

Brand: Samsung Pages: 36

Brand: Samsung Pages: 36

Brand: Samsung Pages: 36

Brand: Samsung Pages: 44

Brand: Samsung Pages: 180

Brand: Samsung Pages: 180

Brand: Samsung Pages: 36

Brand: Samsung Pages: 180

Brand: Samsung Pages: 72

Brand: Colged Pages: 112

Brand: Zanussi Electrolux Pages: 28

Brand: Hoover Pages: 104

Power Wash ELS145

Brand: Clarke Pages: 22

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands