Miele PW 5082 Operating And Installation Instructions Download Page 14 | Manualshive

Page: 14 / 68

background image

Control panel

a

Start

button

Starts the selected programme.

b

Display with –, OK and + buttons

See the following page for more
information.

c

+

button

For selecting delay start.

d

PC / Optical interface

This is used by service technicians
to run diagnostic checks on your
machine and can also be used to
update programming data in the
future.

e

Pre-wash

button

=

with indicator

light

f

Programme selector

For selecting a programme. The
programme selector can be turned
clockwise or anti-clockwise.

g

On-Off

button

s

Before using for the first time

Before using the machine for the first
time ensure that it is correctly
installed and connected. See
"Installation and connection". Also
check that the drain filter is securely
tightened to prevent the risk of leaks
during use.

Commission the machine as described
in the chapter "Before using for the first
time", page 16 in this booklet.

Operating the washer-extractor

14

«
...
12
13
14
15
16
...
»

Summary of Contents for PW 5082





































































Reviews:

No comments

Related manuals for PW 5082

Brand: Zanussi Pages: 20

Brand: Zanussi Pages: 34

Brand: Maidaid Halcyon Pages: 17

Brand: Daewoo Pages: 16

Brand: EdgeStar Pages: 13

Brand: Dawlance Pages: 4

Brand: Maidaid Halcyon Pages: 15

Brand: Magic Chef Pages: 4

Brand: Landa Pages: 36

Brand: V-ZUG Pages: 44

Brand: BOMANN Pages: 15

Brand: Sealey Pages: 4

Brand: Salora Pages: 77

Brand: Haier Pages: 20

Brand: Currys Essentials Pages: 32

Brand: Consolidated Brands Pages: 28

Brand: inventum Pages: 56

Brand: inventum Pages: 92

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands