Miele PT 5137 WP Operating And Installation Instructions Download Page 63

Page: 63 / 68

Standby

To save energy, the display goes out
after 10 minutes and the indicator
light for the

Start

button flashes

slowly.

The display is switched on again by
moving the programme selector or
pressing one of the buttons, without
affecting any programme that is
running.

– On

Standby comes on:
. . . if a programme is not selected.
. . . after the

Start

button has been

pressed in a programme that is
running.
. . . after the end of a programme.

– Not in current prog.

(Factory default)

Standby is activated if no
programme selection is made after
the end of a programme. Standby
will not be activated during a
programme that is running.

Drying levels

The bars show you the setting.

Cottons

Minimum iron

You can alter the drying levels for the

Cottons

and

Minimum iron

programmes.

– from damper

P G G G G G GM

– to drier

P P P P P P P

– Factory default: medium

Machine iron

The

Machine iron

drying level can be

altered separately in the

Cottons

programme.

– from damper

O F F F F F F F F F FM

– to drier

O O O O O O O O O O O

– Factory default: medium

Settings menu

Summary of Contents for PT 5137 WP





































































Search results

Summary of Contents for PT 5137 WP

Reviews:

Related manuals for PT 5137 WP

Brands by name

Popular brands

Miele PT 5137 WP, Operating And Installation Instructions

Search results

Summary of Contents for PT 5137 WP

Reviews:

Related manuals for PT 5137 WP

Brands by name

Popular brands