Miele PT 5137 WP Operating And Installation Instructions Download Page 38 | Manualshive

Page: 38 / 68

background image

Replacing

^

Fit the filter back on the handle. Make
sure it is the correct way round.

To ensure that the filter is positioned
correctly in the front of the heat
exchanger unit:

^

First insert the handle with the filter
attached over the two guide pins.

Make sure that the

yellow dot on

the handle is on the right

.

^

Push the filter in completely.

A programme cannot be started if
the filter is not replaced in the dryer
or is replaced the wrong way round.
A message will appear in the
display.

^

Close the access flap.

,

The filter must be fitted correctly

and the access flap closed to
ensure that water cannot leak from
the condenser system and to ensure
that the dryer functions efficiently.

Cleaning and care

38

«
...
36
37
38
39
40
...
»

Summary of Contents for PT 5137 WP





































































Reviews:

No comments

Related manuals for PT 5137 WP

Brand: Wahl Pages: 128

Brand: Lavex Pages: 12

Brand: V-ZUG Pages: 40

Brand: Grundig Pages: 25

Brand: Orbegozo Pages: 46

Centauro CLGG70214 Series

Brand: mabe Pages: 138

Brand: wad Pages: 27

Brand: Crosley Pages: 8

Brand: Dexter Laundry Pages: 128

Brand: Indesit Pages: 16

Brand: CDA Pages: 40

Brand: Haier Pages: 12

Brand: Haier Pages: 17

Brand: Haier Pages: 22

Brand: Haier Pages: 16

Brand: Haier Pages: 24

Brand: Haier Pages: 92

Brand: Haier Pages: 9

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands