Miele PT 5137 WP Operating And Installation Instructions Download Page 10

Page: 10 / 68

Please observe the instructions in "Installation and connection"

and "Technical data".

The socket must be easily accessible after installation in order to

disconnect the tumble dryer from the electricity supply.

For hard-wired machines, the all-pole isolator provided on-site

must be easily accessible after installation in order to disconnect the
tumble dryer from the electricity supply.

Do not block the gap between the base of the dryer and the floor

with plinth facings, deep pile carpet etc. as this would hinder a
sufficient intake of air.

Make sure the dryer door can be opened without hindrance after

installation.

In areas which may be subject to infestation by cockroaches or

other vermin, pay particular attention to keeping the tumble dryer
and its surroundings in a clean condition at all times. Any damage
which may be caused by cockroaches or other vermin will not be
covered by the appliance guarantee.

Warning and Safety instructions

Summary of Contents for PT 5137 WP





































































Search results

Summary of Contents for PT 5137 WP

Reviews:

Related manuals for PT 5137 WP

Brands by name

Popular brands

Miele PT 5137 WP, Operating And Installation Instructions

Search results

Summary of Contents for PT 5137 WP

Reviews:

Related manuals for PT 5137 WP

Brands by name

Popular brands