Miele PT 5137 WP Operating And Installation Instructions Download Page 33 | Manualshive

Page: 33 / 68

background image

2. When to clean the plinth filter

Normal operation of the dryer

The plinth filter should be cleaned
when the

Clean plinth filter

prompt

appears in the display.

Continuous operation of the dryer

The plinth filter should be cleaned
once a day and also when the
prompt to do so appears in the
display.

The plinth filter is located on the left
of the dryer behind the access panel.
It collects finer fluff, hair and
detergent residues which have got
through the surfaces of the fluff filters
in the door and the door opening.

^

See "Cleaning the plinth filter".

^

Press

OK

to delete the

Clean plinth

filter

prompt.

3. When to clean the grille in the
bottom right/airway

The grille should only be cleaned
when

Open bottom right grille. Clean

airways

appears in the display.

The air cooling vents are located in
the bottom right grille.
The cooling fins behind the grille can
become blocked by dirt particles
drawn in with the room air.

^

Always keep the area around the
tumble dryer free of dust and fluff.
This may make cleaning the bottom
right grille/airway unnecessary.

^

See "Bottom right grille/airway".

^

Press

OK

to delete the

Open bottom

right grille. Clean airways

prompt.

Cleaning and care

33

«
...
31
32
33
34
35
...
»

Summary of Contents for PT 5137 WP





































































Reviews:

No comments

Related manuals for PT 5137 WP

Brand: Maestro Pages: 44

Brand: Yoer Pages: 20

Brand: Chefman Pages: 16

Brand: V-ZUG Pages: 10

Brand: Vidal Sassoon Pages: 4

FreeZone 74200 Series

Brand: Labconco Pages: 65

Brand: Trisa electronics Pages: 25

Brand: INVENTOR Pages: 64

Brand: LANOX Pages: 36

Brand: DryMax Pages: 12

Brand: Caple Pages: 25

Brand: Hyundai Pages: 44

Brand: Beko Pages: 44

Brand: Beko Pages: 44

Brand: Beko Pages: 72

Brand: Beko Pages: 72

Brand: Beko Pages: 44

Brand: Kenmore Pages: 40

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands