Miele PT 5137 WP Operating And Installation Instructions Download Page 30

Page: 30 / 68

Basket Std. temp. (20-90 mins)

max. load in the basket 3 kg

Notes

– The drum does not rotate in this

programme.
For this reason, airing and drying may
only be carried out if the Miele drying
basket (optional accessory) is fitted in
the drum.

– Use this programme to dry items which

are suitable for drying in a tumble dryer
but which are not suitable for drying using mechanical action.

– A satisfactory drying result cannot be achieved without the drying

basket.

– It is essential to observe the operating instructions for the drying

basket.

Use for

– See the operating instructions supplied with the drying basket.

Silks

Max. load 1.5 kg

Use for

Silks, e.g. blouses and shirts

Note

– Remove garments as soon as the programme has finished.

The following programme must be activated by a Service
technician:

Automatic

Max. load 3.5 kg*

, Normal, Hand iron

Use for

– Mixed loads of garments suitable for the

Cottons

and

Minimum iron

programmes

. Sort according to colour.

Weight of dry items

Programme chart

Summary of Contents for PT 5137 WP





































































Search results

Summary of Contents for PT 5137 WP

Reviews:

Related manuals for PT 5137 WP

Brands by name

Popular brands

Miele PT 5137 WP, Operating And Installation Instructions

Search results

Summary of Contents for PT 5137 WP

Reviews:

Related manuals for PT 5137 WP

Brands by name

Popular brands