Miele PT 5137 WP Operating And Installation Instructions Download Page 16 | Manualshive

Page: 16 / 68

background image

Accessories

~

Only use genuine Miele original spare parts and accessories with

this tumble dryer.
If non-Miele parts are used, guarantee, performance and product
liability claims may be invalidated.

~

A Miele tumble dryer can be stacked on top of a Miele washing

machine using the appropriate stacking kit (available as an optional
accessory). Please make sure you order the correct one for the
Miele tumble dryer and Miele washing machine.

~

If installing the machine on a Miele plinth, (available as an

optional accessory), please make sure you order the correct one for
this tumble dryer.

Miele cannot be held liable for damage caused by
non-compliance with these Warning and Safety instructions.

Warning and Safety instructions

16

«
...
14
15
16
17
18
...
»

Summary of Contents for PT 5137 WP





































































Reviews:

No comments

Related manuals for PT 5137 WP

Brand: Maytag Pages: 7

Brand: Taurus Pages: 36

Brand: Daewoo Pages: 12

Brand: Sierra Pages: 25

Brand: V-ZUG Pages: 40

Brand: BaBylissPro Pages: 27

Brand: smith+nobel Pages: 24

Olymp HairMaster

Brand: Belvedere Pages: 28

Brand: Parker Pages: 25

Brand: Danby Pages: 44

Brand: Mediclinics Pages: 24

Brand: Mediclinics Pages: 32

Brand: TriStar Pages: 40

Brand: Kenmore Pages: 1

Brand: Kenmore Pages: 1

Brand: DAN DRYER Pages: 2

Brand: REVLON Pages: 3

Brand: Resfab Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands