Miele PT 5137 WP Operating And Installation Instructions Download Page 11

Page: 11 / 68

Correct use

The maximum load of dry laundry for this tumble dryer is 6.5 kg.

See the Programme chart for the maximum recommended loads in
individual programmes.

Do not let anyone sit or lean on the door, as this can cause the

tumble dryer to tip up. Danger of injury.

Always close the door after use. This way you will avoid the

danger of:

– children climbing into the dryer or hiding things in it.

– pets or other small animals climbing into it.

Do not use a pressure washer or hose to clean the tumble dryer.

Always keep the area around the tumble dryer free of dust and

fluff. Dust drawn into the appliance can cause blockages. Faults can
then occur as well as the risk of fire.

This dryer must not be used:

– without the fluff filters or the plinth filter in place.

– without the grille on the bottom right in place.

– if the fluff filters or plinth filter are damaged in any way.

In the event of any damage, replace them immediately.

This would cause an excessive build-up of fluff which in turn would
cause a fault.

Warning and Safety instructions

Summary of Contents for PT 5137 WP





































































Search results

Summary of Contents for PT 5137 WP

Reviews:

Related manuals for PT 5137 WP

Brands by name

Popular brands

Miele PT 5137 WP, Operating And Installation Instructions

Search results

Summary of Contents for PT 5137 WP

Reviews:

Related manuals for PT 5137 WP

Brands by name

Popular brands