Miele PT 5137 WP Operating And Installation Instructions Download Page 64

Page: 64 / 68

Clean out airways

The electronic unit in the dryer
detects the degree of a blockage
caused by fluff or detergent residues
in the filter, and the following prompt
comes up in the display:

Clean plinth

filter

You can decide at what level of

fluff this message should appear.

You will have an idea of how often this
should be done after a few drying
programmes.

– Off

The prompt does not appear.

In cases of a very severe blockage in
the ducting, the programme is
cancelled and

Clean plinth filter

comes up regardless of this option.

– Heavy

The prompt only appears when there
is a heavy build-up of fluff.

– Normal

(Factory default)

– Light

The prompt appears when there is
only a small build-up of fluff.

Delay start

You can set a later start time using
Delay start (see "Delay start").
You can decide how this time is
displayed.

– Programme end

The finish time for the programme is
selected.

– Programme start

The start time for the programme is
selected.

– Time until start

The time until the start of the
programme is selected in
minutes/hours.

– Off

(Factory default)

By pressing the

button, the time

remaining and the finish time for the
programme is displayed.

Settings menu

Summary of Contents for PT 5137 WP





































































Search results

Summary of Contents for PT 5137 WP

Reviews:

Related manuals for PT 5137 WP

Brands by name

Popular brands

Miele PT 5137 WP, Operating And Installation Instructions

Search results

Summary of Contents for PT 5137 WP

Reviews:

Related manuals for PT 5137 WP

Brands by name

Popular brands