Miele PT 5137 WP Operating And Installation Instructions Download Page 17 | Manualshive

Page: 17 / 68

background image

Control panel

a

Display

After the machine has been switched
on, the display lights up.
As soon as the dryer is ready to use,
the Entry menu appears in the
display.

b

Start button

The indicator light flashes while a
programme is being selected and is
then on constantly after the
programme has started.

c

–, OK, + buttons

See the following pages for more
information.

d

+

button

For selecting delay start; time of day
display

e

PC/Optical interface

This is used by Miele service
technicians during servicing work for
testing purposes.

f

Gentle tumble button

For drying with reduced mechanical
action.

g

Programme selector

The programme selector can be
turned clockwise or anti-clockwise.

h

On/Off button

s

For switching the dryer on and off.
To save energy the dryer will switch
off automatically 15 minutes after the
end of the programme/anti-crease
phase or 15 minutes after the dryer is
switched on if it is not operated.

i

Door button

Opens the machine door
independently of the electricity
supply.

Note regarding the
commissioning of the tumble
dryer

Before using the dryer for the first
time, ensure that it is correctly
installed and connected. See
"Installation and connection" and
"Before using for the first time".

Operating the tumble dryer

17

«
...
15
16
17
18
19
...
»

Summary of Contents for PT 5137 WP





































































Reviews:

No comments

Related manuals for PT 5137 WP

Outdoor Gourmet FSOGBG4003

Brand: Rankam Pages: 18

Brand: Laden Pages: 2

Brand: PowerXL Pages: 44

Brand: Fagor Pages: 39

Brand: Henny Penny Pages: 82

Brand: LabPlant Pages: 16

Dual Basket ProFry 5466

Brand: Presto Pages: 8

Brand: SEVERIN Pages: 56

Brand: Adler Europe Pages: 64

Brand: Adler Europe Pages: 64

Brand: Adler Europe Pages: 68

Brand: Electrolux Pages: 26

Brand: Electrolux Pages: 23

Brand: Electrolux Pages: 32

Brand: Electrolux Pages: 36

Brand: Electrolux Pages: 80

Brand: Electrolux Pages: 2

Brand: Kenmore Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands