Miele G 6365 Operating Instructions Manual Download Page 20

Page: 20 / 92

Before using for the first time

Water hardness

The display changes to the water hard‐
ness setting.

– The dishwasher must be program‐

med for the water hardness in your
area.

– Your local water supplier can tell you

the water hardness level in your area.

– Where the water hardness fluctuates

e.g. between 10 - 16 gr/gal (10 - 15
°d), always program the dishwasher
to the higher value (16 gr/gal or 15 °d
in this example).

It is useful to know your water hardness
so that you can provide the service
technician with this information in the
event of any service calls.

Enter the water hardness below:

____________ gr/gal (°d)

The dishwasher is programmed at the
factory for a water hardness level of 1
gr/gal (1 °d).

Use the

ҟҞ

arrow buttons to select

the hardness of your water supply
and confirm with

See "Settings menu - Water hardness"
for more information.

The message

6HWXSVXFFHVVIXOO\FRP

SOHWHG

will then appear in the display.

After confirming this with

, the

prompts

5HILOOVDOW

and

5HILOOULQVHDLG

may appear.

Add salt and rinse aid if necessary
(see "Before using for the first time -
Dishwasher salt" and "Rinse aid").

Confirm the messages with

The program selected will appear briefly
in the display and the appropriate indi‐
cator light will come on.
Then, the display will show the estimat‐
ed program duration for the program
selected.

These basic settings will be saved in
memory after the dishwasher has been
through one complete program.

Summary of Contents for G 6365





























































































Search results

Summary of Contents for G 6365

Reviews:

Related manuals for G 6365

Brands by name

Popular brands

Miele G 6365, Operating Instructions Manual

Search results

Summary of Contents for G 6365

Reviews:

Related manuals for G 6365

Brands by name

Popular brands