manualshive.com logo in svg

Microscan EZ Match, User Manual

Share
Download
Microscan EZ Match User Manual Download Page 57

EZ Match User’s Manual

3-13

Tube/Cap Inspection

Cap Base Diameter

Cap Tip Diameter

Definition:

The diameter of the cap base (millimeters/10).

Important:

 This dimension should be measured at the bottom (where the 

cap is inserted in the tube), because some caps are tapered.

Serial Cmd:

<

K258,

index,tube diameter,cap base length,cap tip length,

cap base diameter

, 

cap tip diameter,hue,saturation,value

>

Options:

0-32767 (mm/10)

Definition:

If the cap has a tip, this value represents the diameter of the tip in millimeters/10.

Note:

 If this value is 

0

, it will be ignored.

Serial Cmd:

<

K258,

index,tube diameter,cap base length,cap tip length,cap base diameter,

cap 

tip diameter

,hue,saturation,value

>

Options:

0-32767 (mm/10)

Summary of Contents for EZ Match
















































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands