manualshive.com logo in svg

Microscan EZ Match, User Manual

Share
Download
Microscan EZ Match User Manual Download Page 314

12-8

EZ Match User’s Manual

IP Database Status

Any Symbology Type (Add 1)

All symbologies 

except PharmaCode

 are enabled while this database index is being used.

Data Matrix (Add 2)

If enabled, Data Matrix will be active for this database index.

Important:

 The ECC level 

must 

be configured using the Data Matrix command 

<K479>

. If 

no ECC level has been configured, the imager will not decode Data Matrix symbols.

QR Code (Add 4)

If enabled, QR Code will be active for this database index.

Code 128 (Add 8)

If enabled, Code 128 will be active for this database index.

Code 39 (Add 16)

If enabled, Code 39 will be active for this database index.

Codabar (Add 32)

If enabled, Codabar will be active for this database index.

Code 93 (Add 64)

If enabled, Code 93 will be active for this database index.

Interleaved 2 of 5 (Add 128)

If enabled, Interleaved 2 of 5 will be active for this database index.

UPC/EAN (Add 256)

If enabled, UPC/EAN will be active for this database index.

PDF417 (Add 512)

If enabled, PDF417 will be active for this database index.

MicroPDF417 (Add 1024)

If enabled, MicroPDF417 will be active for this database index.

BC412 (Add 2048)

If enabled, BC412 will be active for this database index.

Pharmacode (Add 4096)

If enabled, PharmaCode will be active for this database index.

Summary of Contents for EZ Match
















































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands