Microscan EZ Match User Manual Download Page 296

Page: 296 / 431

11-26

EZ Match User’s Manual

Mirrored Image

Mirrored Image

Regular Image

When

Regular Image

is enabled, images will be processed as they appear upon capture.

Mirrored Image

When

Mirrored Image

is enabled, images will be processed as a reverse of the captured

image.

Both Regular and Mirrored

When

Both

is enabled, regular and mirrored images will be processed.

Usage:

Enable this setting when the imager is viewing a mirrored image (as
when it is being used with a right-angle mirror attachment).

Definition:

When enabled, outputs a mirrored image of the symbol.

Serial Cmd:

K514,mirrored image

Default:

Both (auto-detect)

Options:

0 = Regular Image
1 = Mirrored Image

2 = Both (auto-detect normal/mirrored)

Summary of Contents for EZ Match
















































































































































































































































































































































































































































Search results

Summary of Contents for EZ Match

Reviews:

Brands by name

Popular brands

Microscan EZ Match, User Manual

Search results

Summary of Contents for EZ Match

Reviews:

Brands by name

Popular brands