Microplex logiJET TM4 Operator'S Manual Download Page 134

Page: 134 / 149

134 Troubleshooting

_______________________________________________________________________________________________

MICROPLEX

Operator’s Manual logiJET TM4

Edition 1.2p

[HeadNot Found! ]

- the printhead is not connected or faulty.

[Head defectiv! ]

- the printhead is defective. A new printhead

has to be installed.

[High Head Temp. ]

The printhead temperature is too high.

- make sure the consumables have been
  loaded correctly
  (compare section 4.2 and 4.3)

[Head Life End! ]

- a new printhead has to be installed

[CutterNotFound! ]

The optional cutter is selected, but not

connected or defective.

- make sure the cutter is installed correctly.

[Cutter Error! ]

An error occurred during cutter operation.
- check for a paper jam. Remove the jammed

paper.

- reload the consumables (paper)

If the remedies above are not successful, please call a MICROPLEX
authorized service engineer.

Summary of Contents for logiJET TM4






















































































































































Search results

Summary of Contents for logiJET TM4

Reviews:

Related manuals for logiJET TM4

Brands by name

Popular brands

Microplex logiJET TM4, Operator'S Manual

Search results

Summary of Contents for logiJET TM4

Reviews:

Related manuals for logiJET TM4

Brands by name

Popular brands