manualshive.com logo in svg

Microplex logiJET TM4, Operator'S Manual

Share
Download
Microplex logiJET TM4 Operator'S Manual Download Page 49

                                                                                      Operation     49 

_______________________________________________________________________________________________ 

_______________________________________________________________________________________________ 

MICROPLEX 

Operator’s Manual logiJET TM4 

Edition 1.2p 

 5.3.2.  Setting to Factory Defaults  

 
 

The following key combination is used to back-out all configurations to factory defaults. 

 

 
 
 

 

 
Turn the printer off 

 
 
 

        +

 

 

Turn the printer on 

 

 
 
 
 

 

 
 

Panel display 

 

 
 
 
 

 

 
 
 

 

 

 
 
 
 
Long Beep 

 

 
 

 

 
 

Notes 
 
 
Before starting the printer press the 
 

 

 key     

           

 and             

 
simultaneously. 
 

Turn the printer on and keep the keys  
pressed until both LEDs of the printer 
light up red. 
 

 

Release the keys. 
 
Now (in Offline Mode) press and 
hold the lower key ( >1 second). 
 

 

The configuration of the printer is 
back-outed to factory defaults. 
  

 

READY 
 

 

STATUS 

Summary of Contents for logiJET TM4






















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands