Microplex logiJET TM4 Operator'S Manual Download Page 110

Page: 110 / 149

110 Panel Functions

_______________________________________________________________________________________________

MICROPLEX

Operator’s Manual logiJET TM4

Edition 1.2p

8.3.18. Emulation Selection

This function helps to determine which printer emulation will
be activated.

Panel display

Notes

[Online ]

Turn the printer OFF LINE with this key.

[Menu Level 1 ]

. . .

Press the

key until

[Configuration

] is displayed.

[Configuration ]

Press this key. This selects the Configuration
menu.

[Interface ]

. . .

Press the

key until

[Emulation

] is displayed.

[Emulation ]

Press this key. This selects the Emulation
menu.

[SOLID Standard ]

. . .

Press the

key until the

desired emulation (e.g. HP

PCL

5) is

displayed.

[HP PCL 5 ]

The emulation HP PCL 5 is selected.

[Save as Setup? ]

In addition this new value can be saved as
setup value (using the

key), before

the printer is turned ON LINE again. After
this decision turn the printer ON LINE again:
Press the

key longer than 2 seconds.

[Online ]

Summary of Contents for logiJET TM4






















































































































































Search results

Summary of Contents for logiJET TM4

Reviews:

Related manuals for logiJET TM4

Brands by name

Popular brands

Microplex logiJET TM4, Operator'S Manual

Search results

Summary of Contents for logiJET TM4

Reviews:

Related manuals for logiJET TM4

Brands by name

Popular brands