Microelettrica Scientifica MC2-30T Operation Manual Download

Page: 3 / 70

MC2-30T

Doc. N°

MO-0483-ING

Date

17.03.2022

Rev.

Pag.

17.6.2 - Trip and Alarm __________________________________________________________________________ 35

17.7 - Function:

1I>

(First Overcurrent Element F50/51) _________________________________________________ 37

17.7.1 - Description of variables ___________________________________________________________________ 37

17.7.2 – Blocking Logic (BO-BI) ___________________________________________________________________ 38

17.7.3 - Automatic doubling of Overcurrent thresholds on current inrush ___________________________________ 38

17.8 – Function:

2I>

(Second Overcurrent Element F50/51) _______________________________________________ 39

17.8.1 - Description of variables ___________________________________________________________________ 39

17.9 - Function:

3I>

(Third Overcurrent Element F50/51) _________________________________________________ 39

17.9.1 - Description of variables ___________________________________________________________________ 39

17.10 - Function:

1Io>

(First Earth Fault Element 50N/51N) _______________________________________________ 40

17.10.1 - Description of variables __________________________________________________________________ 40

17.11 - Function:

2Io>

(Second Earth Fault Element 50N/51N) ____________________________________________ 40

17.11.1 - Description of variables __________________________________________________________________ 40

17.12 - Function:

3Io>

(Third Earth Fault Element 50N/51N) ______________________________________________ 41

17.12.1 - Description of variables __________________________________________________________________ 41

17.13 - Function:

1Is>

(First Negative Sequence Element F46) _____________________________________________ 42

17.13.1 - Description of variables __________________________________________________________________ 42

17.13.2 – Time/Current operation of the first Current Unbalance element “f(t)” ______________________________ 42

17.14 - Function:

2Is>

(Second Negative Sequence Element F46) ___________________________________________ 42

17.14.1 - Description of variables __________________________________________________________________ 42

17.15 - Function:

Reclos

(Automatic Reclosure RCL) _____________________________________________________ 43

17.15.1 - Description of variables __________________________________________________________________ 44

17.15.2 – Definitions ____________________________________________________________________________ 44

17.15.3 - Operation ____________________________________________________________________________ 46

17.15.4 - Reclose Command ______________________________________________________________________ 46

17.16 - Function:

tTripRd

(Trip Time Reduction) ________________________________________________________ 47

17.16.1 - Description of variables __________________________________________________________________ 47

17.16.2 - Operation ____________________________________________________________________________ 47

17.17 - Function:

TCS

(Trip Circuit Supervision)_________________________________________________________ 48

18.17.1 - Description of variables __________________________________________________________________ 48

17.17.2 - Operation ____________________________________________________________________________ 48

17.18 - Function:

IRF

(Internal Relay Fault) ____________________________________________________________ 49

17.18.1 - Description of variables __________________________________________________________________ 49

17.18.2 - Operation ____________________________________________________________________________ 49

17.19 - Function:

BreakerFail

(Breaker Failure) ________________________________________________________ 49

17.19.1 - Description of variables __________________________________________________________________ 49

17.19.2 - Operation ____________________________________________________________________________ 49

17.20 - Function:

Oscillo

(Oscillographic Recording) _____________________________________________________ 50

17.20.1 - Description of variables __________________________________________________________________ 50

17.20.2 - Operation ____________________________________________________________________________ 50

17.20.3 – Available on software ___________________________________________________________________ 51

17.20.4 – Setting “User Trigger Oscillo” _____________________________________________________________ 52

17.20.5 – Example: Setting “Oscillo Trigger Logic” _____________________________________________________ 53

17.21 - Function:

CB Mngn

(Control C/B) _____________________________________________________________ 56

17.21.1 - Description of variables __________________________________________________________________ 56

17.21.2 – Push-Buttons (Programmable only via software) ______________________________________________ 56

17.22 - Function:

ExtResCfg

(External Reset Configuration) _______________________________________________ 58

17.22.1 - Description of variables __________________________________________________________________ 58

18. Input – Output (via software) ______________________________________________________________________ 58

18.1 – Digital Input _______________________________________________________________________________ 58

18.2 – “DI” Configuration (via software) _______________________________________________________________ 58

18.2.1 – Example ______________________________________________________________________________ 59

18.2.2 – Name ________________________________________________________________________________ 59

18.2.3 – Status ________________________________________________________________________________ 59

18.2.4 – Functions _____________________________________________________________________________ 59

18.2.5 – Example: Setting “Digital Input” ____________________________________________________________ 59

18.3 – Physical Outputs ____________________________________________________________________________ 60

18.4 - “DO” Configuration __________________________________________________________________________ 60

18.4.1 - Example configuration ____________________________________________________________________ 60

18.4.2 - Functions - Operation Mode ________________________________________________________________ 61

19. InfoStatus _____________________________________________________________________________________ 65

20. Date and Time __________________________________________________________________________________ 66

20.1- Clock synchronization ______________________________________________________________________ 67

22. Healthy (Diagnostic Information) ___________________________________________________________________ 68

23. Dev.Info (Relay Version) __________________________________________________________________________ 68

24. Maintenance ___________________________________________________________________________________ 68

25. Wiring Diagram _________________________________________________________________________________ 69

26. Overall Dimensions ______________________________________________________________________________ 69

27. Electrical Characteristics __________________________________________________________________________ 70

Summary of Contents for MC2-30T




































































Search results

Summary of Contents for MC2-30T

Reviews:

Related manuals for MC2-30T

Brands by name

Popular brands

Microelettrica Scientifica MC2-30T, Operation Manual

Search results

Summary of Contents for MC2-30T

Reviews:

Related manuals for MC2-30T

Brands by name

Popular brands