Microchip Technology Microsemi IGLOO2 User Manual Download Page 101 | Manualshive

Page: 101 / 240

background image

MDDR Subsystem

Microsemi Proprietary UG0446 User Guide Revision 7.0

90

1

RESET_APB_REG

0×0

Full soft reset
If this bit is set when the soft reset bit
is written as ‘1’, all APB registers reset
to the power-up state.

0

REG_DDRC_SOFT_RSTB

0×0

This is a soft reset.
0: Puts the controller into reset.
1: Takes the controller out of reset.
The controller should be taken out of
reset only when all other registers
have been programmed.
Asserting this bit does NOT reset all
the APB configuration registers. Once
the soft reset bit is asserted, the APB
register should be modified as
required.

Table 77 •

DDRC_AXI_FABRIC_PRI_ID_CR

Bit
Number

Name

Reset
Value Description

[31:6]

Reserved

0×0

Software should not rely on the value
of a reserved bit. To provide
compatibility with future products, the
value of a reserved bit should be
preserved across a read-modify-write
operation.

[5:4]

PRIORITY_ENABLE_BIT

0×0

This is to set the priority of the fabric
master ID.
01/10/11: Indicates that the ID is
higher priority. 00: None of the master
IDs from the fabric has a higher
priority.

[3:0]

PRIORITY_ID

0×0

If the Priority Enable bit is 1, this ID will
have a higher priority over other IDs.

Table 78 •

DDRC_SR

Bit
Number Name

Reset
Value

Description

[31:6]

Reserved

0×0

Software should not rely on the value of a
reserved bit. To provide compatibility with future
products, the value of a reserved bit should be
preserved across a read-modify-write operation.

Table 76 •

DDRC_DYN_SOFT_RESET_ALIAS_CR

(continued)

Bit
Number Name

Reset
Value Description

«
...
99
100
101
102
103
...
»

Summary of Contents for Microsemi IGLOO2

















































































































































































































































Reviews:

No comments

Related manuals for Microsemi IGLOO2

Brand: Datavideo Pages: 50

Brand: Waterous Pages: 90

Brand: Campbell Pages: 14

SATURA SPOT LED PRO

Brand: Elation Pages: 41

Brand: Tapco Pages: 16

Brand: Zenbooth Pages: 40

Visium CytAssist

Brand: 10x Genomics Pages: 51

Chromium X Series

Brand: 10x Genomics Pages: 5

Brand: Tascam Pages: 80

Brand: Tascam Pages: 2

Brand: Walker Pages: 24

ENET-232 Series

Brand: National Instruments Pages: 105

Brand: Octane Fitness Pages: 20

Brand: Oceaneering Pages: 27

Brand: Xtricity Pages: 4

INTEGRA ARINC e-NAV

Brand: Kannad Pages: 20

Brand: IN Pages: 6

Brand: Selecta Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands