Mhouse MhouseKit WG2S, Instructions For Installation And Use Manual

Page: 36 / 132

English
2 – English
GENERAL SAFETY WARNINGS AND PRECAUTIONS
This may damage product components and cause malfunctions, fire
or hazardous situations. If this occurs, suspend installation immediately
and contact the Nice Technical Assistance.
• Never make modifications to any part of the product. Operations oth -
er than as specified can only cause malfunctions. The manufacturer
declines all liability for damage caused by makeshift modifications to the
product.
• If the power cable is damaged, it must be replaced exclusively by a
qualified technician, to avoid potential risks.
• Connect the control unit to an electric power line equipped with an
earthing system.
• This product is not designed to be used by persons (including children)
whose physical, sensorial or mental capacities are reduced, or with lack
of experience or skill, unless suitable instructions regarding use of the
product have been provided by a person responsible for safety.
• The key-operated selector switch must be positioned in sight of the
automation, but far from moving parts and at a height of at least 1.5 m
from the ground, not accessible by the public. If this is used in “hold-
to-run” mode, ensure that there are no persons in the vicinity of the
automation.
• In the vicinity of the automation children must be supervised to ensure
that they do not play with it.
• Ensure that there are not points of entrapment or crushing with fixed
parts when the gate leaf is in the maximum opening or closing position;
protect parts if necessary.
• The product may not be considered an efficient system of protection
against intrusion. If an efficient protection system is required, the auto -
mation must be integrated with other safety devices.
• The automation must not be used before performing the commission -
ing procedure as specified in the chapter “Testing and commissioning”.
• Check the automation frequently to ensure there is no imbalance, signs
of wear or damage to electrical or mechanical parts. Do not use the
automation if adjustments or repairs are necessary.
• In the event of long periods of disuse, to avoid the risk of leaks of harm -
ful substances from the optional battery (PR1) disconnect it from the
automation and store in a dry location.
• Do not allow children to play with fixed control devices. Keep remote
control devices out of reach of children.
• The product’s packaging materials must be disposed of in full compli -
ance with local regulations.
Operation warnings
• For cleaning the product surfaces, use a soft damp cloth. Use water
only; never use detergents or solvents for cleaning.
––– STEP 1 –––
Safety warnings
• CAUTION! – This manual contains important instructions and
warnings for personal safety.
Incorrect installation could cause seri-
ous physical injury. Carefully read all parts of this manual before starting
any work. If in doubt, suspend installation immediately and contact the
Nice Technical Assistance.
• CAUTION! – Important instructions: keep this manual in a safe
place to enable future product maintenance and disposal proce -
dures.
• CAUTION! – According to the most recent European legislation,
the production of a power-operated door or gate must com -
ply with the standards envisaged in the Directive 2006/42/EC
(Machinery Directive) and in particular standards EN 12445; EN
12453; EN 12635 and EN 13241-1, which enable declaration of
presumed conformity of the automation. In consideration of this,
all mains connection, testing, commissioning and maintenance
operations must be performed exclusively by a qualified and
skilled technician.
All preliminary set-up, installation and programming operations
may be performed by personnel with standard skills, provided
that all instructions and the relative sequences in this manual
are strictly observed, with particular reference to the warnings in
this STEP 1.
Installation warnings
While reading this manual, take care to observe all instructions
marked with the following symbol:
These symbols indicate subjects that may be the source of poten -
tial hazards and therefore the prescribed operations must be per -
formed exclusively by qualified and skilled personnel, in obser -
vance of these instructions current safety standards.
• Before installation, ensure that this product is suitable for automation of
your gate or door (see STEP 3 and chapter “Product Technical Specifi -
cations”). If not suitable, do NOT proceed with installation.
• On the system power mains install a device for disconnection (not sup -
plied), to guarantee a gap between contacts and complete disconnec -
tion in the conditions of overvoltage category III.
• All installation and maintenance operations must be performed
with the automation disconnected from the power supply.
If the
power disconnect device is not visible from the location of the automa -
tion, before work a notice should be affixed on the disconnect device,
with the text “CAUTION! MAINTENANCE IN PROGRESS”.
• CAUTION! - Never power up the motor before fully installed on
the column and leaf of the gate.
• During installation, handle the automation with care, avoiding the risk
of impact, dropping or contact with any type of liquid. Never place the
product near to sources of heat and never expose to naked flames.
KNOWLEDGE OF THE PRODUCT AND PREPARATION FOR INSTALLATION
––– STEP 2 –––
2.1 - PRODUCT DESCRIPTION AND INTENDED USE
The devices in this kit, plus other accessories (some optional and not
included in the pack), form the automation system named “WG2S”,
designed for the automation of a “residential” swing gate. Any other
use than as specified herein or in environmental conditions other
than as stated in this manual is to be considered improper and is
strictly prohibited!
The main part of the automation comprises one control unit and two elec -
tromechanical gearmotors, each equipped with a 24 V DC motor, a worm
reducer and a mechanical locking system with key to enable manual
opening and closing of the gate in the event of a power failure.
The control unit comprises a board and incorporated radio receiver which
receives the commands sent by the user via a transmitter. It can memo -
rise up to 256 GTX4 transmitters (if memorised in “Mode I”) and up to 6
pairs of PH100 photocells.
NOTES TO MANUAL
• This manual describes how to set up a complete and optimal
automation, such as that shown in fig. 6, using all Mhouse devic -
es that are part of the automation system named “WG2S”. Some
of these devices are optional and may not be present in the kit.
For a complete overview of the devices, refer to the Mhouse
product catalogue.
• This manual has been drawn up as a step-by-step guide . There-
fore, to ensure safe and facilitated assembly and programming
procedures, perform all operations described in the same order
as specified in this document.