Mercury 92-858058K01 Page 72 Manual Download

Page: 72 / 150

Section 3 - On the Water

Page 64

90-879172181

eng

FEBRUARY 2011

•

Pressed one of the "TURN" (course adjust) buttons with Auto Heading engaged.

a -

"TURN" button

b -

"RESUME" button

c -

"AUTO HEADING" button

Disengaging Auto Heading

1. Disengage the Auto Heading mode with any of the following actions:

•

Place the ERC handles for all engines in neutral. The "AUTO HEADING" button light turns off and the Standby light

comes on.

•

Turn the steering wheel beyond the electronic detent. The "AUTO HEADING" button light turns off and the Resume light

comes on.

•

Press the "AUTO HEADING" button on the Precision Pilot keypad. The "AUTO HEADING" button light turns off and the

Standby light comes on.

a -

"TURN" button

b -

"RESUME" button

c -

"AUTO HEADING" button

2. A single horn beep sounds and the mode indicator changes from "AUTO" to "OFF".

27700

Summary of Contents for 92-858058K01























































































































































Search results

Summary of Contents for 92-858058K01

Reviews:

Related manuals for 92-858058K01

Brands by name

Popular brands

Mercury 92-858058K01, Manual

Search results

Summary of Contents for 92-858058K01

Reviews:

Related manuals for 92-858058K01

Brands by name

Popular brands