Mercury 92-858058K01 Manual Download

Page: 19 / 150

Section 2 - Getting to Know Your Power Package

90-879172181

eng

FEBRUARY 2011

Page 11

SmartCraft 2.2 Control System

The control system option used on your vessel can be identified by the following:
•

Two separate Vessel Interface Panels (VIP), one for each engine system.

43914

Typical SmartCraft 2.2 VIP

SmartCraft 3.0 Control System

The control system option used on your vessel can be identified by the following:
•

One or more auxiliary joystick station installed

•

All triple and quad systems (some dual systems)

•

The vessel is equipped with three helm stations

•

One single VIP for all engine systems

43913

Typical SmartCraft 3.0 VIP

Features and Controls

E‑Stop (Emergency Stop) Switch, If Equipped

An E‑stop (emergency stop) switch turns off the engines in an emergency situation, such as a person overboard or a tangled

propeller. When activated, an E‑stop switch interrupts the power supply to the engine and transmission. The E‑stop switch turns

off all of the engines when the switch is at the helm or an auxiliary joystick station.

Typical E-stop switch at the helm

a -

"E‑STOP" switch

34014

Summary of Contents for 92-858058K01























































































































































Search results

Summary of Contents for 92-858058K01

Reviews:

Related manuals for 92-858058K01

Brands by name

Popular brands

Mercury 92-858058K01, Manual

Search results

Summary of Contents for 92-858058K01

Reviews:

Related manuals for 92-858058K01

Brands by name

Popular brands